User manual SKIL 7375

[. . . ] MULTI SANDER 7370 (F0157370. . ) 7375 (F0157375. . ) ME77 GB F D NL S DK N FIN E P I H CZ TR PL ORIGINAL INSTRUCTIONS . 61 INSTRUCIUNI DE FOLOSIRE ORIGINALE . 45 OR<J<NAL <fiLETME TAL<MATI . 91 www. skileurope. com SKIL Europe BV - Konijnenberg 60 4825 BD Breda - The Netherlands 12/08 2609001133 1 7370 240 Watt 1, 6 kg EPTA 01/2003 28000 p/min 7375 240 Watt 1, 6 kg EPTA 01/2003 28000 p/min 2 H G J J A B F D C E 3 4 2 5 B 6 B 2 A C 1 3 1 A C 7 B 8 A D 3 9 B E A 0 F F ! 4 3 2 1 @ 4 # $ % 5 ^ & 4 3 1 2 * 6 GB Multi sander INTRODUCTION 7370/7375 This tool is intended for dry sanding and finishing of wood, painted surfaces, plastic and filler Read and save this instruction manual 3 TECHNICAL SPECIFICATIONS 1 TOOL ELEMENTS 2 A B C D E F G H J Delta tip Button for changing foot plates Rectangle Support plate (7375) Louvre attachment (7375) Dust box On/off switch Pressure control (7375) Ventilation slots SAFETY GENERAL SAFETY INSTRUCTIONS WARNING! [. . . ] SAFETY INSTRUCTIONS FOR SANDERS Avoid damage that can be caused by screws, nails and other elements in your workpiece; remove them before you start working Always keep the cord away from moving parts of the tool; direct the cord to the rear, away from the tool When you put away the tool, switch off the motor and ensure that all moving parts have come to a complete standstill Use completely unrolled and safe extension cords with a capacity of 16 Amps (U. K. 13 Amps) In case of electrical or mechanical malfunction, immediately switch off the tool and disconnect the plug We recommend to use original SKIL-accessories as listed at the back of this instruction manual This tool should not be used by people under the age of 16 years The noise level when working can exceed 85 dB(A); wear ear protection If the cord is damaged or cut through while working, do not touch the cord, but immediately disconnect the plug Never use the tool when cord is damaged; have it replaced by a qualified person Always check that the supply voltage is the same as the voltage indicated on the nameplate of the tool (tools with a rating of 230V or 240V can also be connected to a 220V supply) This tool is not suitable for wet sanding Secure the workpiece (a workpiece clamped with clamping devices or in a vice is held more securely than by hand) Do not work materials containing asbestos (asbestos is considered carcinogenic) Dust from material such as paint containing lead, some wood species, minerals and metal may be harmful (contact with or inhalation of the dust may cause allergic reactions and/or respiratory diseases to the operator or bystanders); wear a dust mask and work with a dust extraction device when connectable Certain kinds of dust are classified as carcinogenic (such as oak and beech dust) especially in conjunction with additives for wood conditioning; wear a dust mask and work with a dust extraction device when connectable Follow the dust-related national requirements for the materials you want to work with When sanding metal, sparks are generated; do not use dustbox and keep other persons and combustible material from work area Do not touch the moving sanding sheet Do not continue to use worn, torn or heavily clogged sanding sheets Wear protective gloves, safety glasses, close-fitting clothes and hair protection (for long hair) Always disconnect plug from power source before making any adjustment or changing any accessory WHEN CONNECTING NEW 3-PIN PLUG (U. K. ONLY): Do not connect the blue (= neutral) or brown (= live) wire in the cord of this tool to the earth terminal of the plug If for any reason the old plug is cut off the cord of this tool, it must be disposed of safely and not left unattended USE Mounting of sanding sheet 4 !the dust suction requires the use of perforated sanding sheets !perforation in sanding sheet should correspond with perforation in sanding foot !always use the tool with the total sanding surface covered with sanding paper WHEN USING TOOL AS AN ORBITAL SANDER 5 - remove delta tip A while pushing button B - mount rectangle C by inserting tabs in holes at a 45 angle and pushing it towards housing until it snaplocks - mount VELCRO sanding sheet as illustrated (do not remove part 2) WHEN USING TOOL AS A DELTA SANDER 6 - remove rectangle C while pushing button B - mount delta tip A by inserting tabs in holes at a 45 angle and pushing it towards housing until it snaplocks - mount VELCRO sanding sheet as illustrated (remove part 2 and keep it for using tool as an orbital sander) Mounting support plate 7 (7375) - remove VELCRO sanding sheet - remove delta tip A while pushing button B - mount support plate D as illustrated Mounting special sanding attachments 8 (7375) - mount desired sanding attachment to support plate D as illustrated 8 - mount corresponding VELCRO sanding sheet to sanding attachment - 3 sanding positions Mounting "Louvre" attachment 9 (7375) - remove VELCRO sanding sheet - remove delta tip A while pushing button B - mount "Louvre" attachment as illustrated Dust suction 0 - empty dustbox F regularly for optimal dust pick-up performance !do not use dustbox when sanding metal Pressure control !(7375) Warns the user when applying too much pressure on the tool while working (too much pressure reduces the sanding performance) - green light 1 turns on when running tool is placed on workpiece - green light 2 turns on in case of pressure - green light 3 turns on in case of increased pressure - red light 4 turns on when pressure is too high On/off switch - switch on/off the tool by pushing switch G 2 forward/backwards !before the sanding surface reaches the workpiece, you should switch on the tool !before switching off the tool, you should lift it from the workpiece Holding and guiding the tool @ - guide the tool parallel to the working surface !do not apply too much pressure on the tool; let the sanding surface do the work for you - do not tilt the tool in order to avoid unwanted sanding marks !NOISE/VIBRATION Measured in accordance with EN 60 745 the sound pressure level of this tool is 85 dB(A) and the sound power level 96 dB(A) (standard deviation: 3 dB), and the vibration 14 (7370) / 11 (7375) m/s2 (hand-arm method; uncertainty K = 1. 5 m/s2). Technical file at: SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL. F CE DCLARATION DE CONFORMIT Nous dclarons sous notre propre responsabilit que ce produit est en conformit avec les normes ou documents normaliss suivants: EN 60 745, EN 55 014, conforme aux rglementations 2006/95/CE, 2004/108/CE, 98/37/CE (jusqu'au 28. 12. 2009), 2006/42/CE ( partir du 29. 12. 2009). BRUIT/VIBRATION Mesur selon EN 60 745 le niveau de la pression sonore de cet outil est 85 dB(A) et le niveau de la puissance sonore 96 dB(A) (dviation standard: 3 dB), et la vibration 14 (7370) / 11 (7375) m/s2 (mthode main-bras; incertitude K = 1, 5 m/s2). Dossier technique auprs de: SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL. D CE KONFORMITTSERKLRUNG Wir erklren in alleiniger Verantwortung, da dieses Produkt mit den folgenden Normen oder normativen Dokumenten bereinstimmt: EN 60 745, EN 55 014, gem den Bestimmungen der Richtlinien 2006/95/EG, 2004/108/EG, 98/37/EG (bis 28. 12. 2009), 2006/42/EG (ab 29. 12. 2009). GERUSCH/VIBRATION Gemessen gem EN 60 745 betrgt der Schalldruckpegel dieses Gertes 85 dB(A) und der Schalleistungspegel 96 dB(A) (Standard- abweichung: 3 dB), und die Vibration 14 (7370) / 11 (7375) m/s2 (Hand-Arm Methode; unsicherheit K = 1, 5 m/s2). Technische Unterlagen bei: SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL. CE CONFORMITEITSVERKLARING Wij verklaren, dat dit product voldoet aan de volgende normen of normatieve documenten: EN 60 745, EN 55 014, overeenkomstig de bepalingen van de richtlijnen 2006/95/EG, 2004/108/EG, 98/37/EG (tot 28-12-2009), 2006/42/EG (vanaf 29-12-2009). GELUID/VIBRATIE Gemeten volgens EN 60 745 bedraagt het geluidsdrukniveau van deze machine 85 dB(A) en het geluidsvermogen-niveau 96 dB(A) (standaard deviatie: 3 dB), en de vibratie 14 (7370) / 11 (7375) m/s2 (hand-arm methode; onzekerheid K = 1, 5 m/s2). Technisch dossier bij: SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL. CE KONFORMITETSFRKLARING Vi intygar och ansvarar fr, att denna produkt verensstmmer med fljande norm och dokument: EN 60 745, EN 55 014, enl. bestmmelser och riktlinjema 2006/95/EG, 2004/108/EG, 98/37/EG (till 28. 12. 2009), 2006/42/EG (from 29. 12. 2009). [. . . ] ZGOMOT/VIBRAII Msurat n conformitate cu EN 60 745 nivelul de presiune a sunetului generat de acest instrument este de 85 dB(A) iar nivelul de putere a sunetului 96 dB(A) (abaterea standard: 3 dB), iar nivelul vibraiilor 14 (7370) / 11 (7375) m/s2 (metoda mn - bra; incertitudine K = 1, 5 m/s2). Documentaie tehnic la: SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL. CE KPA A COTETCTBE , : EN 60 745, EN 55 014, 2006/95/EG, 2004/108/EG, 98/37/EG ( 28. 12. 2009), 2006/42/EG ( 29. 12. 2009). /PA EN 60 745 85 dB(A) 96 dB(A) ( : 3 dB), 14 (7370) / 11 (7375) m/s2 ( -; K = 1, 5 m/s2). [. . . ]