User manual SKIL 7450

[. . . ] ) ME77 GB F D NL S DK N FIN E P I H CZ TR PL ORIGINAL INSTRUCTIONS . 60 INSTRUCIUNI DE FOLOSIRE ORIGINALE . 43 OR<J<NAL <fiLETME TAL<MATI . 89 www. skileurope. com SKIL Europe BV - Konijnenberg 60 4825 BD Breda - The Netherlands 05/08 2610396376 1 7440 380 Watt 2, 3 kg EPTA 01/2003 2mm 11000 P/MIN 125mm 7450 430 Watt 2, 3 kg EPTA 01/2003 2mm 11000 P/MIN 125mm 7460 430 Watt 2, 3 kg EPTA 01/2003 2mm 6000-11000 P/MIN 125mm 2 E (7450/7460) G F H (7460) 3 K J D A B C 2 4 5 7450/7460 4 3 2 1 J D 6 7 7460 8 3 9 40 - 80 5-7 7460 80 - 240 5-7 40 - 120 7 120 - 240 5 40 - 120 5-7 2 4 0 4 ACCESSORIES COARSE MEDIUM FINE EXTRA FINE 40 (5x) 60 (5x) 120 (5x) 240 (5x) SKIL Nr. 2610383122 2610383123 2610383124 2610383125 2610396225 2610384703 2610384702 5 GB Random orbit sander 7440/7450/7460 INTRODUCTION This tool is intended for dry sanding of wood, plastic, metal, filler and painted surfaces Read and save this instruction manual 3 TECHNICAL SPECIFICATIONS 1 TOOL ELEMENTS 2 A B C D E F G H J K Backing pad Pad screw Sanding disc Dust box Pressure control (7450/7460) On/off switch Knob for locking on/off switch Sanding speed selection wheel (7460) Knob for removing dustbox Ventilation slots SAFETY GENERAL SAFETY INSTRUCTIONS WARNING! [. . . ] g) Use the power tool, accessories and tool bits etc. , in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation. 5) SERVICE a) Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained. SAFETY INSTRUCTIONS FOR SANDERS Avoid damage that can be caused by screws, nails and other elements in your workpiece; remove them before you start working Always keep the cord away from moving parts of the tool; direct the cord to the rear, away from the tool When you put away the tool, switch off the motor and ensure that all moving parts have come to a complete standstill Use completely unrolled and safe extension cords with a capacity of 16 Amps (U. K. 13 Amps) In case of electrical or mechanical malfunction, immediately switch off the tool and disconnect the plug SKIL can assure flawless functioning of the tool only when original accessories are used This tool should not be used by people under the age of 16 years The noise level when working can exceed 85 dB(A); wear ear protection If the cord is damaged or cut through while working, do not touch the cord, but immediately disconnect the plug Never use the tool when cord is damaged; have it replaced by a qualified person Always check that the supply voltage is the same as the voltage indicated on the nameplate of the tool (tools with a rating of 230V or 240V can also be connected to a 220V supply) This tool is not suitable for wet sanding Do not work materials containing asbestos (asbestos is considered carcinogenic) When sanding metal, sparks are generated; do not use dustbox and keep other persons and combustible material from work area Do not touch the moving sanding disc Do not continue to use worn, torn or heavily clogged sanding discs Wear protective gloves, safety glasses, close-fitting clothes and hair protection (for long hair) Dust from material such as paint containing lead, some wood species, minerals and metal may be harmful (contact with or inhalation of the dust may cause allergic reactions and/or respiratory diseases to the operator or bystanders); wear a dust mask and work with a dust extraction device when connectable Certain kinds of dust are classified as carcinogenic (such as oak and beech dust) especially in conjunction with additives for wood conditioning; wear a dust mask and work with a dust extraction device when connectable Follow the dust-related national requirements for the materials you want to work with Always disconnect plug from power source before making any adjustment or changing any accessory WHEN CONNECTING NEW 3-PIN PLUG (U. K. ONLY): Do not connect the blue (= neutral) or brown (= live) wire in the cord of this tool to the earth terminal of the plug If for any reason the old plug is cut off the cord of this tool, it must be disposed of safely and not left unattended USE Backing pads - never run the tool without backing pad A !replace damaged backing pads immediately (loosen/fasten 4 pad screws B) !unplug tool before removing/mounting backing pads Mounting sanding discs - simply press sanding disc C onto backing pad with perforation in sanding disc corresponding with perforation in backing pad - if necessary, clean backing pad first !the dust suction requires the use of perforated sanding discs Dust suction 4 - empty dustbox D regularly for optimal dust pick-up performance - remove dustbox D by pushing knob J to the left and hold it in that position while pulling dustbox D backwards - mount dustbox D by sliding it back until it clicks into place !do not use dustbox when sanding metal Pressure control 5 (7450/7460) Warns the user when applying too much pressure on the tool while working (too much pressure reduces the sanding performance) - green light 1 turns on in case of pressure - green light 2/3 turns on in case of increased pressure - red light 4 turns on when pressure is too high 7 NOTES: - the pressure control feature is specifically designed for fast sanding at maximum sanding speed (speed control setting 7), for it is the need for fast sanding that provokes applying too much pressure !be aware that the working of the pressure control feature is not guaranteed when sanding at lower speed control settings (1-6) On/off - before switching on the tool, you should place it with the entire sanding surface on the workpiece - when switching on, do not apply too much pressure on the tool - switch on/off the tool by pulling/releasing trigger F !be aware of the sudden impact when the tool is switched on !before switching off the tool, you should lift it from the workpiece Switch lock 6 - pull trigger F - press knob G with your thumb - release the trigger - unlock the switch by pulling again trigger F and then releasing it Speed control 7 (7460) For optimal sanding results on different materials - with wheel H 2 you can adjust the sanding speed steplessly from minimum to maximum - always adjust speed to grit size used - before starting a job, find the optimal speed by testing out on spare material Holding and guiding the tool 8 !while working, always hold the tool at the greycoloured grip area(s) - guide the tool parallel to the working surface and move it in circles or in a cross pattern !NOISE/VIBRATION Measured in accordance with EN 60 745 the sound pressure level of this tool is 82 dB(A) and the sound power level 93 dB(A) (standard deviation: 3 dB), and the vibration 7. 7 m/s2 (hand-arm method; uncertainty K = 1. 5 m/s2). Technical file at: SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL. F CE DCLARATION DE CONFORMIT Nous dclarons sous notre propre responsabilit que ce produit est en conformit avec les normes ou documents normaliss suivants: EN 60 745, EN 55 014, conforme aux rglementations 2006/95/CE, 2004/108/CE, 98/37/CE (jusqu'au 28. 12. 2009), 2006/42/CE ( partir du 29. 12. 2009). BRUIT/VIBRATION Mesur selon EN 60 745 le niveau de la pression sonore de cet outil est 82 dB(A) et le niveau de la puissance sonore 93 dB(A) (dviation standard: 3 dB), et la vibration 7, 7 m/s2 (mthode main-bras; incertitude K = 1, 5 m/s2). Dossier technique auprs de: SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL. D CE KONFORMITTSERKLRUNG Wir erklren in alleiniger Verantwortung, da dieses Produkt mit den folgenden Normen oder normativen Dokumenten bereinstimmt: EN 60 745, EN 55 014, gem den Bestimmungen der Richtlinien 2006/95/EG, 2004/108/EG, 98/37/EG (bis 28. 12. 2009), 2006/42/EG (ab 29. 12. 2009). GERUSCH/VIBRATION Gemessen gem EN 60 745 betrgt der Schalldruckpegel dieses Gertes 82 dB(A) und der Schalleistungspegel 93 dB(A) (Standard- abweichung: 3 dB), und die Vibration 7, 7 m/s2 (Hand-Arm Methode; unsicherheit K = 1, 5 m/s2). Technische Unterlagen bei: SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL. NL CE CONFORMITEITSVERKLARING Wij verklaren, dat dit product voldoet aan de volgende normen of normatieve documenten: EN 60 745, EN 55 014, overeenkomstig de bepalingen van de richtlijnen 2006/95/EG, 2004/108/EG, 98/37/EG (tot 28-12-2009), 2006/42/EG (vanaf 29-12-2009). GELUID/VIBRATIE Gemeten volgens EN 60 745 bedraagt het geluidsdrukniveau van deze machine 82 dB(A) en het geluidsvermogen-niveau 93 dB(A) (standaard deviatie: 3 dB), en de vibratie 7, 7 m/s2 (hand-arm methode; onzekerheid K = 1, 5 m/s2). [. . . ] Y / Y EN 60 745 82 dB(A) o 93 dB(A) ( : 3 dB), 7, 7 m/s2 ( / - K = 1, 5 m/s2). : SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL. 08 SKIL Europe BV A. Kloot 94 RO DECLARAIE DE CONFORMITATE CE Declarm pe proprie rspundere c acest product este conform cu urmtoarele standarde sau documente standardizate: EN 60 745, EN 55 014, n conformitate cu regulile 2006/95/CE, 2004/108/CE, 98/37/CE (pn la 28. 12. 2009), 2006/42/CE (ncepnd cu 29. 12. 2009). ZGOMOT/VIBRAII Msurat n conformitate cu EN 60 745 nivelul de presiune a sunetului generat de acest instrument este de 82 dB(A) iar nivelul de putere a sunetului 93 dB(A) (abaterea standard: 3 dB), iar nivelul vibraiilor 7, 7 m/s2 (metoda mn - bra; incertitudine K = 1, 5 m/s2). [. . . ]