User manual SKIL 7640

[. . . ] ) ME77 GB F D NL S DK N FIN E P I H CZ TR PL ORIGINAL INSTRUCTIONS . 61 INSTRUCIUNI DE FOLOSIRE ORIGINALE . 43 OR<J<NAL <fiLETME TAL<MATI . 91 www. skileurope. com SKIL Europe BV - Konijnenberg 60 4825 BD Breda - The Netherlands 03/08 2610398857 1 7640 900 Watt 3, 6 kg EPTA 01/2003 76 mm 130x76 mm 220-340 m/min 533 mm 7650 900 Watt 3, 7 kg EPTA 01/2003 76 mm 130x76 mm 220-340 m/min 533 mm 2 A C K L B G* J* H* F E MD * NOT STANDARD INCLUDED 3 4 C 2 5 D E 6 H (NOT STANDARD INCLUDED) G (NOT STANDARD INCLUDED) J (NOT STANDARD INCLUDED) 3 7 L 8 K 9 0 N (NOT STANDARD INCLUDED) ! 4 GB Belt sander INTRODUCTION 7640/7650 This tool is intended for dry sanding with high removal performance of wood, plastic, metal, filler and painted surfaces Read and save this instruction manual 3 TECHNICAL SPECIFICATIONS 1 TOOL ELEMENTS 2 A B C D E F G H J K L M N On/off switch Knob for locking on/off switch Sanding speed selection wheel Lever for changing sanding belt Arrow Knob for adjusting belt centering Dust box* Dust bag* Vacuum cleaner adapter* Auxiliary handle Knob for adjusting auxiliary handle Ventilation slots Sanding frame* * NOT STANDARD INCLUDED SAFETY GENERAL SAFETY INSTRUCTIONS WARNING! [. . . ] g) Use the power tool, accessories and tool bits etc. , in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation. 5) SERVICE a) Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained. SAFETY INSTRUCTIONS FOR SANDERS Avoid damage that can be caused by screws, nails and other elements in your workpiece; remove them before you start working Always keep the cord away from moving parts of the tool; direct the cord to the rear, away from the tool When you put away the tool, switch off the motor and ensure that all moving parts have come to a complete standstill Use completely unrolled and safe extension cords with a capacity of 16 Amps (U. K. 13 Amps) In case of electrical or mechanical malfunction, immediately switch off the tool and disconnect the plug SKIL can assure flawless functioning of the tool only when original accessories are used This tool should not be used by people under the age of 16 years The noise level when working can exceed 85 dB(A); wear ear protection If the cord is damaged or cut through while working, do not touch the cord, but immediately disconnect the plug Never use the tool when cord is damaged; have it replaced by a qualified person Always check that the supply voltage is the same as the voltage indicated on the nameplate of the tool (tools with a rating of 230V or 240V can also be connected to a 220V supply) This tool is not suitable for wet sanding Do not work materials containing asbestos (asbestos is considered carcinogenic) Dust from material such as paint containing lead, some wood species, minerals and metal may be harmful (contact with or inhalation of the dust may cause allergic reactions and/or respiratory diseases to the operator or bystanders); wear a dust mask and work with a dust extraction device when connectable Certain kinds of dust are classified as carcinogenic (such as oak and beech dust) especially in conjunction with additives for wood conditioning; wear a dust mask and work with a dust extraction device when connectable Follow the dust-related national requirements for the materials you want to work with When sanding metal, sparks are generated; do not use dustbag/dustbox/vacuum cleaner and keep other persons and combustible material from work area Do not touch the running sanding belt Do not continue to use worn, torn or heavily clogged sanding belts Wear protective gloves, safety glasses, close-fitting clothes and hair protection (for long hair) Always disconnect plug from power source before making any adjustment or changing any accessory WHEN CONNECTING NEW 3-PIN PLUG (U. K. ONLY): Do not connect the blue (= neutral) or brown (= live) wire in the cord of this tool to the earth terminal of the plug If for any reason the old plug is cut off the cord of this tool, it must be disposed of safely and not left unattended USE On/off switch - switch on/off the tool by pulling/releasing trigger A 2 !before the sanding surface reaches the workpiece, you should switch on the tool !before switching off the tool, you should lift it from the workpiece Switch locking for continuous use - pull trigger A 2 - press knob B 2 with your thumb - release the trigger - unlock the switch by pulling again trigger A 2 and then releasing it Speed control for smooth starting 4 For optimal sanding results on different materials - with wheel C you can set the desired sanding speed - adjust speed to grit size used - before starting a job, find the optimal speed and grit by testing out on spare material 6 Quick-changing of sanding belts (CLIC system) 5 !disconnect the plug - lift lever D - remove sanding belt - insert new belt with arrows printed at inner side of belt pointing in same direction as arrow E on tool - push lever back !never fold sanding belts In case belt runs off tool (mostly caused by inferior belt quality), you should - switch on the tool - turn knob F 2 till the sanding belt is running in line with the flat side of the tool - use new belt, if belt still runs off tool Dust suction 6 - empty dustbox G/dustbag H regularly for optimal dust pick-up performance - when using tool with vacuum cleaner, mount vacuum cleaner adaptor J as illustrated - when necessary, also clean the small filters as illustrated !do not use dustbox/dustbag/vacuum cleaner when sanding metal Auxiliary handle 7 - loosen knob L almost completely - adjust handle K to desired position - tighten knob L firmly Holding and guiding the tool 8 !while working, always hold the tool at the greycoloured grip area(s) - guide the tool parallel to the working surface !NOISE/VIBRATION Measured in accordance with EN 60 745 the sound pressure level of this tool is 90 dB(A) and the sound power level 101 dB(A) (standard deviation: 3 dB), and the vibration 6. 3 m/s2 (hand-arm method; uncertainty K = 1. 5 m/s2). Technical file at: SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL. F CE DCLARATION DE CONFORMIT Nous dclarons sous notre propre responsabilit que ce produit est en conformit avec les normes ou documents normaliss suivants: EN 60 745, EN 55 014, conforme aux rglementations 2006/95/CE, 2004/108/CE, 98/37/CE (jusqu'au 28. 12. 2009), 2006/42/CE ( partir du 29. 12. 2009). BRUIT/VIBRATION Mesur selon EN 60 745 le niveau de la pression sonore de cet outil est 90 dB(A) et le niveau de la puissance sonore 101 dB(A) (dviation standard: 3 dB), et la vibration 6, 3 m/s2 (mthode main-bras; incertitude K = 1, 5 m/s2). Dossier technique auprs de: SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL. D CE KONFORMITTSERKLRUNG Wir erklren in alleiniger Verantwortung, da dieses Produkt mit den folgenden Normen oder normativen Dokumenten bereinstimmt: EN 60 745, EN 55 014, gem den Bestimmungen der Richtlinien 2006/95/EG, 2004/108/EG, 98/37/EG (bis 28. 12. 2009), 2006/42/EG (ab 29. 12. 2009). GERUSCH/VIBRATION Gemessen gem EN 60 745 betrgt der Schalldruckpegel dieses Gertes 90 dB(A) und der Schalleistungspegel 101 dB(A) (Standard- abweichung: 3 dB), und die Vibration 6, 3 m/s2 (Hand-Arm Methode; unsicherheit K = 1, 5 m/s2). Technische Unterlagen bei: SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL. NL CE CONFORMITEITSVERKLARING Wij verklaren, dat dit product voldoet aan de volgende normen of normatieve documenten: EN 60 745, EN 55 014, overeenkomstig de bepalingen van de richtlijnen 2006/95/EG, 2004/108/EG, 98/37/EG (tot 28-12-2009), 2006/42/EG (vanaf 29-12-2009). GELUID/VIBRATIE Gemeten volgens EN 60 745 bedraagt het geluidsdrukniveau van deze machine 90 dB(A) en het geluidsvermogen-niveau 101 dB(A) (standaard deviatie: 3 dB), en de vibratie 6, 3 m/s2 (hand-arm methode; onzekerheid K = 1, 5 m/s2). Technisch dossier bij: SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL. S CE KONFORMITETSFRKLARING Vi intygar och ansvarar fr, att denna produkt verensstmmer med fljande norm och dokument: EN 60 745, EN 55 014, enl. bestmmelser och riktlinjema 2006/95/EG, 2004/108/EG, 98/37/EG (till 28. 12. 2009), 2006/42/EG (from 29. 12. 2009). [. . . ] Y / Y EN 60 745 90 dB(A) o 101 dB(A) ( : 3 dB), 6, 3 m/s2 ( / - K = 1, 5 m/s2). : SKIL Europe BV (PT-SEU/PJE), 4825 BD Breda, NL. 08 SKIL Europe BV A. Kloot 98 RO DECLARAIE DE CONFORMITATE CE Declarm pe proprie rspundere c acest product este conform cu urmtoarele standarde sau documente standardizate: EN 60 745, EN 55 014, n conformitate cu regulile 2006/95/CE, 2004/108/CE, 98/37/CE (pn la 28. 12. 2009), 2006/42/CE (ncepnd cu 29. 12. 2009). ZGOMOT/VIBRAII Msurat n conformitate cu EN 60 745 nivelul de presiune a sunetului generat de acest instrument este de 90 dB(A) iar nivelul de putere a sunetului 101 dB(A) (abaterea standard: 3 dB), iar nivelul vibraiilor 6, 3 m/s2 (metoda mn - bra; incertitudine K = 1, 5 m/s2). [. . . ]