User manual SKIL 9950

[. . . ] POLISHER 9950 (F0159950. . ) GB F D NL S DK N FIN E P I H CZ TR PL RU ORIGINAL INSTRUCTIONS NOTICE ORIGINALE ORIGINALBETRIEBSANLEITUNG ORIGINELE GEBRUIKSAANWIJZING BRUKSANVISNING I ORIGINAL ORIGINAL BRUGSANVISNING ORIGINAL BRUKSANVISNING ALKUPERÄISET OHJEET MANUAL ORIGINAL MANUAL ORIGINAL ISTRUZIONI ORIGINALI EREDETI HASZNÁLATI UTASÍTÁS PVODNÍM NÁVODEM K POUZÍVÁNÍ ORJNAL LETME TALMATI INSTRUKCJA ORYGINALNA 4 8 12 17 22 26 30 35 39 44 48 53 58 63 67 72 UA GR RO BG SK HR 78 83 88 93 98 103 107 111 116 120 124 137 134 INSTRUCIUNI DE FOLOSIRE ORIGINALE PÔVODNÝ NÁVOD NA POUZITIE ORIGINALNE UPUTE ZA RAD SRB ORIGINALNO UPUTSTVO ZA RAD SLO IZVIRNA NAVODILA EST ALGUPÄRANE KASUTUSJUHEND LV LT AR FA ORIINL LIETOSANAS PAMCBA ORIGINALI INSTRUKCIJA www. skilmasters. com SKIL Europe BV - Konijnenberg 60 4825 BD Breda - The Netherlands 08/09 ME77 2610399871 1 9950 1300 Watt EPTA 01/2003 3, 3 kg 10003000/min M14 Ø 125 mm Ø 180 mm RUBBER 2 3 B M N H NK L D E A F J G C 2 4 5 B 180º A C 6 7 8 3 GB Polisher INTRODUCTION 9950 · This tool is intended for polishing metal, plastic and coated surfaces as well as for the polishing of stone materials without the use of water · Read and save this instruction manual 2 TECHNICAL SPECIFICATIONS 1 TOOL ELEMENTS 3 A B C D E F G H J K L M N Auxiliary handle Auxiliary handle (type D) Hex key Spindle Rubber plate Clamping flange Spanner Spindle-lock button Wool bonnet On/off switch Knob for locking on/off switch Wheel for maximum speed control Ventilation slots SAFETY GENERAL SAFETY INSTRUCTIONS WARNING!Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. [. . . ] After inspecting and installing an accessory, position yourself and bystanders away from the plane of the rotating accessory and run the power tool at maximum no load speed for one minute. Damaged accessories will normally break apart during this test time. i) Wear personal protective equipment 4. Depending on application, use face shield, safety goggles or safety glasses. As appropriate, wear dust mask, hearing protectors, gloves and shop apron capable of stopping small abrasive or workpiece fragments. The eye protection must be capable of stopping flying debris generated by various operations. The dust mask or respirator must be capable of filtrating particles generated by your operation. Prolonged exposure to high intensity noise may cause hearing loss. j) Keep bystanders a safe distance away from work area. Anyone entering the work area must wear personal protective equipment. Fragments of the workpiece or of a broken accessory may fly away and cause injury beyond the immediate area of operation. k) Hold the power tool only by the insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own power cord. Contact with a "live" wire will also make exposed metal parts of the power tool "live" and shock the operator. l) Position the cord clear of the spinning accessory. If you lose control, the cord may be cut or snagged and your hand or arm may be pulled into the spinning accessory. m) Never lay the power tool down until the accessory has come to a complete stop. The spinning accessory may grab the surface and pull the power tool out of your control. n) Do not run the power tool while carrying it at your side. Accidental contact with the spinning accessory could snag your clothing, pulling the accessory into your body. o) Regularly clean the power tool's air vents. The motor's fan will draw the dust inside the housing and excessive accumulation of powdered metal may cause electrical hazards. p) Do not operate the power tool near flammable materials. [. . . ] c) N'exposez pas l'outil électroportatif à la pluie ou à l'humidité. La pénétration d'eau dans un outil électroportatif augmente le risque d'un choc électrique. d) N'utilisez pas le câble à d'autres fins que celles prévues, n'utilisez pas le câble pour porter l'appareil ou pour l'accrocher ou encore pour le débrancher de la prise de courant. Maintenez le câble éloigné des sources de chaleur, des parties grasses, des bords tranchants ou des parties de l'appareil en rotation. [. . . ]