User manual SKIL F0155255AH

[. . . ] Com 7 Circular saw INTRODUCTION 5255 ? This tool is intended for lengthways and crossways cutting of wood with straight cuts as well as angle cuts up to 45; with the appropriate saw blades also non-ferrous metals, light building materials and plastics can be cut ? This tool is not intended for professional use ? Read and save this instruction manual 2 TECHNICAL DATA 1 SAFETY GENERAL SAFETY INSTRUCTIONS WARNING!Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. [. . . ] The protruding blade may cut objects that can cause kickback. 3) LOWER GUARD FUNCTION a) Check lower guard for proper closing before each use. Do not operate the saw if lower guard does not move freely and close instantly. Never clamp or tie the lower guard into the open position. If saw is accidentally dropped, lower guard may be bent. Disconnect the plug, raise the lower guard with the retracting handle and make sure it moves freely and does not touch the blade or any other part, in all angles and depths of cut. B) Check the operation of the lower guard spring. If the guard and the spring are not operating properly, they must be serviced before use. Lower guard may operate sluggishly due to damaged parts, gummy deposits, or a build-up of debris. C) Lower guard should be retracted manually only for special cuts such as plunge cuts and compound cuts. Raise lower guard by retracting handle and as soon as blade enters the material, the lower guard must be released. For all other sawing, the lower guard should operate automatically. D) Always observe that the lower guard is covering the blade before placing saw down on bench or floor. An unprotected, coasting blade will cause the saw to walk backwards, cutting whatever is in its path. Be aware of the time it takes for the blade to stop after switch is released. When bevel cutting, cutting depth does not correspond with value on cutting depth scale ? 90 Cutting angle check 5 - adjust and tighten foot K to maximum cutting depth 4 - adjust and tighten cutting angle to 0 - check for a 90 angle between the blade and bottom of foot with a square - if adjustment is needed, loosen knob M and use adjustment screw P as illustrated ? Adjustable saw line visor Q 6a - for guiding tool along desired line of cut marked on the workpiece - for a straight 0 cut or a 45 bevel cut use the indicator line concerned !The wide part of the foot should rest on the supported part of the workpiece - can be adjusted to allow you to choose whether waste material is on inner or outer side of blade 6b !Cutting width is determined by width of blade teeth and not by width of blade body !Always make trial cuts first to verify actual line of cut ? Dust suction - connect vacuum cleaner to extension R 7 !Never let the vacuum cleaner hose interfere with the lower guard or the cutting operation - one may also use a dust bag (SKIL accessory 2610387402) ? Operating the tool 7 - connect plug to power source - always hold handle S firmly with one hand and handle T firmly with the other hand - place tool with front end of foot flat on workpiece !Ensure that the saw teeth are not engaged into the workpiece - switch on tool by first pressing knob V (= safety switch which cannot be locked) and then pulling trigger W !The tool should run at full speed before the blade enters into the workpiece - lower guard F opens automatically when saw blade enters the workpiece (open lower guard manually by using lever G only for special cuts such as plunge cuts) ! [. . . ] t?ia?i piese de prelucrat extrem de mici ? Nu lucra?i cu scula deasupra capului ? n caz de blocare sau de defec?iune electric?sau mecanic?, deconecta?i imediat scula ?i decupla?i cablul ? n cazul n care cordonul este deteriorat sau sec?ionat n timpul lucrului, nu atinge?i cordonul, dar deconecta?i imediat de la priz?UTILIZARE ? Cnd pune?i instrumentul la o parte, deconecta?i motorul ?i asigura?i-v?toate elementele mobile ?i-au oprit complet mi?carea ? Dup? [. . . ]