User manual SKYMASTER A4 ARF PRO

[. . . ] 1/5. 5 Scale Almost-Ready-To-Fly RC Jet Assembly and operations manual Spesifications Type : T. A. V. S ARF PRO Scale : 1/5. 5th Length : 85. 5 " (2225mm) Span : 61": (1550mm) Weight : 25--32 Lbs ( 12. 5--14 Kg) Engine : 23--30 Lbs (10--14 Kg) trust Radio : 12 Channel 8--12 servo's) The A4 Skyhawk by Skymaster Thank you very much for purchasing our Skymaster ARF PRO A4. Please note that the photos in this instruction manual show certain views from the prototypes. Some modifications and upgrades might have taken place by the release of the model. We have tried to produce a very scale replica of this classic jet. [. . . ] If not, please read it again before you start the assembly. P-8 Kit Contents Assembly & Operation Manual Photo A A4 ARF PRO Contents: Picture A Fuselage front and rear including nose gear + door installed + speed brake installed. Left and right wings incl landing gear and doors installed Left and right stabilizers and elevators Fin and rudder Carbon main spar and stab spar Pitot tubes Refueling probe Aresting hook P-9 Assembly & Operation Manual OPTIONAL PARTS Landing Gear Photo 1 3 x Air Tanks 1 x Retract Valve 2 x Filler & 2 x Pressure Gauges 1 x Electronic Brake Valve 5 x Air Tubing, 10 x Quick Disconnect 8 x T-pieces, 2 x 4 way Fuel Tank (2) 3. 5L Photo 2 Pushrod Set Photo 3 Photo 4 Airpower Optional 5 in 1 Electronic Valve & Sequencer Control Brake, Gear and Doors Photo 5 Stainless Steel Tail Pipe Cockpit P-10 Photo 6 Photo 7 Assembly & Operation Manual Servo mounting hardware Photo 8 Bolts & Accessory pack Photo 9 L/G hydrolic set Carbon Bypass Photo 10 Photo 11 Tygon Tubing Tank Hardware Photo 12 Photo 13 P-11 Assembly & Operation Manual CONTROL LINKAGES Flaps : 63mm (2) Aileron : 62mm (2) Elevator : 80mm (2) Steering: 10 mm Photo 14 WINGS NOTE: Make sure to have some sort of protective foam on the work bench. This will protect the paint surface from unwanted dents. Mark each step. operation of Landing gear and doors. Check Remove factory self tapping L/G screws and replace with high quality screws. Inspect landing gear blocks. Make sure all parts are glued. Photo 15 quick disconnects to air line. the operation of brake Check Remove and mark servo covers and inspect plywood. Use dremel to clean out some glue and ply to make sure servos will fit well. Photo 16 P-12 Assembly & Operation Manual all items needed to complete wings. Fit 2 L-shape Locate servo brackets to 1 x JR DS8411 servos. servo must be mounted with horns facing Aileron Photo 17 up. The horn must be closest to control surface and furthest away for root. servo horns and centre servo's with TX. Secure Photo 18 a line perpendicular to hinge line. Drill horn 1. 5mm for link Mark Dremel to mill slot for control horns. Use 30 minute epoxy to glue control horns Use epoxy cured, insert After pushrods and secure safety clips. Photo 19 operation of aileron. Check slot in servo cover and secure with 4 x 1mm set screws. Mill Remove L/G cover to locate flap servo mount. Check servo for flap function on radio and fasten servo. Setup for at least 45 degree deflection of flaps. Check Photo 20 Photo 21 P-13 Assembly & Operation Manual up 2 flap pushrods. Make location of hole in L/G pod for pushrod. Mark pushrod through hole in L/G pod and fasten Slide with safety clips Photo 23 flap horn and sand bottom. Rough carbon to Locate make sure good contact with glue. Drill 1. 5mm hole for link. line on flap in line with flap pushrod Draw location of flap horn . [. . . ] Choose a fine day for the maiden flight. Select take off flap or flight mode 1 and open throttle. Gently pull back on stick 50m down the runway. Raise the flaps and gear at safe altitude and let the model sit on rails. Slow Flight Most of the first flight should be utilized to get familiar with the slow speed flight characteristics. [. . . ]