User manual SMART DEVICES SG1130BX

[. . . ] For service or installation assistance, please call our Technical Support Department between the hours of 8 a. m-5 p. m. 1-800-45-SMART LIMITED WARRANTY: SMART products and accessories are warranted against malfunction or failure due to defects in workmanship or materials for a period of one year from the date of shipment. If a problem occurs during the warranty period, the unit will be repaired, or replaced at our option, without charge for materials or labor. If air freight is requested by the dealer, the difference between air and surface charges will be billed to the dealer. [. . . ] Each call answered is connected to the announcement in progress. As long as the caller remains on the line, the announcement will continue to play until the maximum call hold time has been reached. As each caller hangs up, the line become immediately available to answer another call. When all of the lines 2. 2 Side Panel Controls and Connections 12 VDC To connect the external DC power pack. POWER This switch enables external power to the system. AUDIO IN This connector provides input from the Digital Announcer. LCD CONTRAST Adjusts the contrast of the LCD display to compensate for lighting variations. CONTROL OUT Interface to control the play operation of the Digital Announcer. CONTROL IN 3 SRS-3 STEREO PROCESSOR return to the idle state, the Announcer continues to run. 4. 3 Multiple SMART CTR2000's A single SMART CTR2000 supports up to 8 telephone lines. For applications requiring more than 8 lines, additional SMART CTR2000 systems can be added. Display call counts 5 ­ 8 Next Day III Display call counts 5 ­ 8 Action Display call counts 1 ­ 4 Display call counts 1 ­ 4 5. 1. 2 Line Configuration Display The Line Configuration Display indicates whether or not a telephone line is enabled to answer calls. An "I" indicates that the telephone line is enabled, a "O" indicates that the telephone line is disabled, a "T" indicates that the telephone line is operating under Timed Operation and " " indicates that the line card is absent. The Line Configuration Display first shows Monday's configuration, to see Tuesday's configuration press "I", etc. Press "Clr" at any time to stop reviewing the Line Configurations. Mon = 1 2 3 4 5 6 7 8 (Tue) T I I T T O ­ ­ Function Key Action 5 CTR2000 CONCENTRATOR Function Key I II III IV No ­ Exit no change in call counts digit is a "1" then the units digit may be (0 2). Action Yes ­ Clears count ALL lines Enter Month?01/05/95 09:30:32 AM Valid Keys (0 ­ 9) Clr ­ Advance to Day without making change To Exit ­ Automatically after 15 seconds 5. 2. 1. 2 Set Time and Date ­ Enter Day (tens digit) Entering the day, the system checks that the day entered is valid between 01 and 31. The tens digit must be between "0 ­ 3". To Exit press "CLR" or automatically after 15 seconds 5. 2 Programming Mode Menu The Programming Mode provides access to setting the time and date and system configuration parameters. Function Key I II III IV Change system configuration Action Set time and date Set time and date Enter Day?01/05/95 09:30:32 AM Valid Keys (0-3) Clr ­ Advance to Year without making change To Exit ­ Automatically after 15 seconds 5. 2. 1. 3 Set Time and Date ­ Enter Day (units digit) Entering the day, the system checks that the day entered is valid between 01 and 31. To Exit press "CLR" or automatically after 15 seconds 5. 2. 1 Set Time and Date ­ Enter Month (tens digit) Entering the month, the system checks that the month entered is valid between 01 and 12. The tens digit may be between "0 5". Enter Hour? [. . . ] 08:30 AM Valid Keys (0 ­ 9) To Exit ­ Press "CLR" or automatically after 15 seconds 5. 2. 2. 10. 3 Change Answer Stop Time ­ Enter AM or PM After the hour is entered, the user is asked to select either AM or PM. Function Key I II III IV Selects PM Action Selects AM Enter Minutes?08:30 AM Valid Keys (0 ­ 9) To Exit ­ Press "CLR" or automatically after 15 seconds 5. 2. 2. 10 Time to Stop Answering Calls The current time to stop answering calls is shown. To change that time, Press "IV" (No), if no change is desired, Press "I" (Yes). [. . . ]