User manual SMC EZ1026GLSC

[. . . ] SMC-EZ1026DT V. 2 EZ Switch 10/100 SMC-1026DT V. 2 Unmanaged Ethernet/Fast Ethernet Switch User Guide 1 SMC-EZ1026DT V. 2 Table of Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1. 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 1. 2 Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] UTP cable with RJ45 connectors/ Fiber cable with MT-RJ/ VF-45 connectors: Check if the cable and connectors work properly. A power outlet: 100 to 240V AC at 50 to 60 Hz: Make sure that the Switch power is accessible and cables can be connected easily. Dedicated power supply: Use a dedicated power circuits or power conditioners to supply reliable electrical power to the network devices. A dry cool place: Keep the Switch away from moisture. Avoid 9 SMC-EZ1026DT V. 2 direct sunlight, heat source, and high amount of electromagnetic interference around. Mounting tools: If you intend to mount the Switch on a rack, make sure you have all the tools, mounting brackets, screws etc. Caution: Cabling must be away from sources of electrical noise such as radio, computers, transmitters, broadband amplifiers, power lines and keep away from TVs, hair dryers, and microwave. Airflow around the Switch and through its vents on the rear cannot be restricted. 3. 2 Mounting the Switch The SMC-EZ1026DT V. 2 Switch is suitable for use in an office environment where it can be rack-mounted in standard EIA 19-inch racks or standalone. Desktop Mounting 1. Set the Switch on a sufficiently large flat space with a power outlet nearby, and about the center of all networked devices. Make sure mounting surface on the bottom of the Switch is grease dust free. Remove adhesive backing from your Rubber Feet. Figure 3-1. Attaching Rubber Feet to each corner on the bottom of the Switch 10 SMC-EZ1026DT V. 2 4. Apply the Rubber Feet to each corner on the bottom of the Switch. These footpads can prevent the Switch from shock/vibrations. Caution: Do not place objects on top of the Switch. Rack-mounted Installation The SMC-EZ1026DT V. 2 Switch come with a rack-mounted kit and can be mounted in an EIA standard size, 19-inch Rack. The Switch can be placed in a wiring closet with other equipment. Perform the following steps to rack mount the Switch: A. Position one bracket to align with the holes on one side of the Switch and secure it with the smaller bracket screws. Then attach the remaining bracket to the other side of the Switch. Figure 3-2. After attached both mounting brackets, position the SMC-EZ1026DT V. 2 Switch ( UTP/MT-RJ/VF-45 ) in the rack by lining up the holes in the brackets with the appropriate holes on the rack. Secure the Switch to the rack with a screwdriver and the rack-mounting screws. 11 SMC-EZ1026DT V. 2 Figure 3-3. Mount the 24TP+1Fiber Module Switch in an EIA Standard 19-inch Rack Note: For proper ventilation, allow about at least 4 inches (10 cm) of clearance on the front and 3. 4 inches ( 8 cm ) on the back of the Switch. [. . . ] All ports can connect to high-speed department servers that need high bandwidth. This Switch provides parallel communications within it's Gigabit port, which can run up to 2000 Mbps at Full-duplex. The Switch makes key servers available to more users by allowing multiple conversations to occur concurrently, thereby significantly expanding overall network throughput. Moreover, this Switch eases supervision and maintenance by allowing network manager centralize multiple servers in a single location. 22 SMC-EZ1026DT V. 2 Figure 4-2: Departmental Bridge Application NOTE: Full-duplex operation only applies to point-to-point access (for example, when attaching the Switch to a workstation, server, or another Switch). [. . . ]