User manual SMC 7004VBR

[. . . ] BarricadeTM Broadband Router Broadband Router with 4-Port Switch N N N N N N Multi-User Internet Access via Single User Account EZ 3-Click Installation Wizard Configurable Parental Control Stateful Packet Inspection and DoS Support Supports a Wide Variety of Internet Applications Virtual Private Network Using PPTP, L2TP, IPSec Pass-Through User Guide SMC7004VBR BarricadeTM Broadband Router User Guide From SMC's Barricade line of Broadband Routers September 2002 Part Number: 150200009800A Revision Number: EU 01 COMPLIANCES FCC - Class B This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with instructions, may cause harmful interference to radio communications. However, there is no guarantee that the interference will not occur in a particular installation. [. . . ] You can dynamically assign TCP/IP address settings to a client, or you can manually configure a client with address settings to meet your specific network requirements. (Note that the default IP address of the Barricade is 192. 168. 2. 1. ) 5-6 CONFIGURING CLIENT TCP/IP Windows XP 1. Click the "start" button and choose "Control Panel. " 2. Select the "Network and Internet Connections" icon, then click the "Network Connections" icon, and double click on the "LAN or High-Speed Internet. " 3. Press the "Properties" button in the "General" tab. Select the TCP/IP line that has been assigned to your network card in the "Local Area Connection Properties" window. Click the "Properties" button to set the TCP/IP protocol for the Barricade. 6. You can dynamically assign TCP/IP address settings to a client, or you can manually configure a client with address settings to meet your specific network requirements. (Note that the default IP address of the Barricade is 192. 168. 2. 1. ) 5-7 SETTING UP TCP/IP TO WORK WITH THE BARRICADE Configuring Your Computer with Windows 95/98/ME You may find that the instructions here do not exactly match your version of Windows. This is because these steps and screenshots were created in Windows 98. Windows 95 and Windows Millennium Edition are very similar, but not identical, to Windows 98. Configure TCP/IP Settings After you have completed the hardware setup by connecting your devices, you need to configure the computer to connect to the Barricade. You need to determine how your ISP issues your IP address. Many ISPs issue these numbers automatically using a networking technology known as Dynamic Host Control Protocol, or DHCP. Other ISPs will specify your IP address and associated numbers, which you must enter manually. This is also known as a static IP address. How your ISP assigns your IP address determines how you will configure your computer. From the Windows desktop, click "Start/Settings/Control Panel. " 5-8 CONFIGURING CLIENT TCP/IP 2. Double-click the "Network" icon. 3. On the "Network" window "Configuration" tab, double-click the "TCP/IP" entry for your network card. 5-9 SETTING UP TCP/IP TO WORK WITH THE BARRICADE 4. If "Obtain an IP address automatically" is already checked, your computer is already configured for DHCP. Click "Cancel" to close each window, and skip to "Step 2. [. . . ] SMC is responsible for return shipping charges from SMC to customer. i LIMITED WARRANTY WARRANTIES EXCLUSIVE: IF A SMC PRODUCT DOES NOT OPERATE AS WARRANTED ABOVE, CUSTOMER'S SOLE REMEDY SHALL BE REPAIR OR REPLACEMENT OF THE PRODUCT IN QUESTION, AT SMC'S OPTION. THE FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF ALL OTHER WARRANTIES OR CONDITIONS, EXPRESSED OR IMPLIED, EITHER IN FACT OR BY OPERATION OF LAW, STATUTORY OR OTHERWISE, INCLUDING WARRANTIES OR CONDITIONS OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. SMC NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR IT ANY OTHER LIABILITY IN CONNECTION WITH THE SALE, INSTALLATION, MAINTENANCE OR USE OF ITS PRODUCTS. SMC SHALL NOT BE LIABLE UNDER THIS WARRANTY IF ITS TESTING AND EXAMINATION DISCLOSE THE ALLEGED DEFECT IN THE PRODUCT DOES NOT EXIST OR WAS CAUSED BY CUSTOMER'S OR ANY THIRD PERSON'S MISUSE, NEGLECT, IMPROPER INSTALLATION OR TESTING, UNAUTHORIZED ATTEMPTS TO REPAIR, OR ANY OTHER CAUSE BEYOND THE RANGE OF THE INTENDED USE, OR BY ACCIDENT, FIRE, LIGHTNING, OR OTHER HAZARD. [. . . ]