User manual SMC 7500A/VCP

[. . . ] TigerAccess Extended Ethernet System Extended Ethernet System High-speed Internet access over existing phone lines Supports 24 Extended Ethernet lines Optional 1000BASE-X modules Concurrent data and telephone services (voice/ISDN) over a single connection Supports evolving ETSI, ANSI, and ITU standards for the copper local loop Spanning Tree Protocol Supports port trunks QoS support for four-level priority Full support for VLANs with GVRP IGMP multicast filtering and snooping Manageable via console, RMON Management Guide SMC7724M/VSW TigerAccess Extended Ethernet System Management Guide From SMC's Tiger line of feature-rich workgroup LAN solutions 38 Tesla Irvine, CA 92618 Phone: (949) 679-8000 December 2002 Pub. # 150200022300A Information furnished by SMC Networks, Inc. (SMC) is believed to be accurate and reliable. However, no responsibility is assumed by SMC for its use, nor for any infringements of patents or other rights of third parties which may result from its use. [. . . ] You can use the end command to return to the Privileged Exec mode. Console(config)#interface ethernet 1/5 Console(config-if)#exit Console(config)#line console Console(config-line)# Command Line Processing Commands are not case sensitive. You may abbreviate commands and parameters as long as they contain enough letters to differentiate them from other currently available commands or parameters. Use the Tab key to complete partial commands, or enter a partial command followed by the "?" character to display a list of possible matches. You may also use the following editing keystrokes for command-line processing: Keystroke Ctrl-A Ctrl-B Ctrl-E Ctrl-P Ctrl-U Ctrl-W Function Shifts cursor to start of command line. Deletes the last word typed. Delete key or backspace key Erases a mistake when entering a command. 3-9 COMMAND LINE INTERFACE Command Groups The system commands can be broken down into the functional groups shown below. Command Group General Flash/File System Management Radius Client SNMP IP Description Basic commands for entering privileged access mode, restarting the system, or quitting the CLI Manages code image or switch configuration files Controls system logs, system passwords, user name, browser management options, and a variety of other system information Configures RADIUS client-server authentication for logon access Activates authentication failure traps; configures community access strings, and trap managers Configures the IP address and gateway for management access, DHCP server and relay service for server blades, displays the default gateway, or pings a specified device Configures the connection parameters for all Ethernet ports, aggregated links, and VLANs Configures the address table for filtering specified addresses, displaying current entries, clearing the table, or setting the aging time Configures secure addresses for a port Configures Spanning Tree settings for the switch Configures VLAN settings, and defines port membership for VLAN groups Enables or configures Private VLAN Configures GVRP settings that permit automatic VLAN learning; shows the configuration for bridge extension MIB Configures IGMP multicast filtering, querier eligibility, query parameters, and specifies ports attached to a multicast router Page 3-12 3-19 3-26 3-39 3-44 3-51 Interface Address Table 3-68 3-79 Port Security Spanning Tree VLAN PVLAN GVRP and Bridge Extension IGMP Snooping 3-84 3-85 3-95 3-105 3-105 3-114 3-10 COMMAND GROUPS Command Group Priority Description Sets port priority for untagged frames, relative weight for each priority queue, and the maximum number of queues enabled; also sets priority for TCP/UDP traffic types, IP precedence, and DSCP Mirrors data to another port for analysis without affecting the data passing through or the performance of the monitored port Statically groups multiple ports into a single logical trunk; configures Link Aggregation Control Protocol for port trunks Configures and displays communication parameters for VDSL and Ethernet ports on the switch and connected CPEs Controls the maximum rate for traffic transmitted or received on a port Page 3-124 Monitor Port 3-138 Port Trunking and LACP VDSL 3-141 3-146 Rate Limit 3-163 3-11 COMMAND LINE INTERFACE General Commands Command enable disable configure reload end Function Activates privileged mode Mode NE Page 3-13 3-14 3-15 3-16 3-17 Returns to normal mode from privileged PE mode Activates global configuration mode Restarts the system Returns to Privileged Exec mode PE PE GC, IC, LC, VC any NE, PE any any exit quit help ? Returns to the previous configuration mode, or exits the CLI Exits a CLI session Shows how to use help Shows options for command completion (context sensitive) 3-17 3-18 NA NA Note: The access mode shown in the table is indicated by these abbreviations: NE (Normal Exec), PE (Privileged Exec), GC (Global Configuration), IC (Interface Configuration), LC (Line Configuration), VC (VLAN Database Configuration. ) 3-12 GENERAL COMMANDS enable Use this command to activate Privileged Exec mode. In privileged mode, additional commands are available, and certain commands display additional information. See "Understanding Command Modes" on page 3-7. Syntax enable [level] level - Privilege level to log in to the device. The device has two predefined privilege levels: 0: Normal Exec, 15: Privileged Exec. Enter level 15 to access Privileged Exec mode. Default Setting Level 15 Command Mode Normal Exec Command Usage · "super" is the default password required to change the command mode from Normal Exec to Privileged Exec. (To set this password, see the enable password command on page 3-29. ) · The "#" character is appended to the end of the prompt to indicate that the system is in privileged access mode. Setting the password for Level 0 has no effect. 3-13 COMMAND LINE INTERFACE · You cannot set a null password with the enable password command. You will have to enter a password to access the Privileged Exec mode. Example Console#enable Console# Related Commands disable enable password disable Use this command to return to Normal Exec mode from privileged mode. In normal access mode, you can only display basic information on the switch's configuration or VDSL/Ethernet statistics. To gain access to all commands, you must use the privileged mode. See "Understanding Command Modes" on page 3-7. Default Setting None Command Mode Privileged Exec Command Usage The ">" character is appended to the end of the prompt to indicate that the system is in normal access mode. Example Console#disable Console> Related Commands enable 3-14 GENERAL COMMANDS configure Use this command to activate Global Configuration mode. You must enter this mode to modify any settings on the switch. You must also enter Global Configuration mode prior to enabling some of the other configuration modes, including Interface Configuration, Line Configuration, and VLAN Database Configuration. [. . . ] Use the [D]elete File command to remove a runtime or diagnostic file that is not set as the startup file (i. e, the S/Up setting for the file must be set to "0" before it can be deleted). Press <x> to start to download the new code file. If using Windows HyperTerminal, click the "Transfer" button, and then click "Send File. . . . " Select the XModem Protocol and then use the "Browse" button to select the required firmware code file from your PC system. The "Xmodem file send" window displays the progress of the download procedure. [. . . ]