User manual SMEG 6091

[. . . ] Electrical connection ________________________________ 9 5. 1 Clearances above and around domestic appliances ________________________10 6. Gas connection ___________________________________ 12 6. 1 Connection to liquid gas ______________________________________________12 6. 2 Room ventilation ____________________________________________________12 6. 3 Combustion gas discharge ____________________________________________12 7. Adapting to different types of gas______________________ 13 7. 1 7. 2 7. 3 7. 4 7. 5 7. 6 7. 7 7. 8 Removing the hob skin _______________________________________________13 Burner and nozzle characteristics table __________________________________14 Hob burner layout ___________________________________________________14 Adjusting the primary air flow __________________________________________14 Reassembling the hob skin____________________________________________15 Adjusting the minimum setting for natural gas _____________________________15 Adjusting the minimum setting for liquid gas_______________________________15 Greasing the gas taps________________________________________________15 8. Description of controls ______________________________ 16 8. 1 The front panel _____________________________________________________16 9. [. . . ] It will act as a cushion between the surface of the surround and that of the cabinet. The diagram on the right shows the correct position for the foam rubber strip. Take great care when fitting it to ensure that it does not project beyond the outside edge of the frame. 4. 3 Fitting the fixing clips Fit the fixing clips in all the points marked with an arrow. The clips fix the hob an ensure that it is centred correctly. To fit the clips to the hob, simply press them gently horizontally into the groove provided (fig. Then turn them upwards to fix them permanently in place (fig. B). 4. 4 Fitting the hob into the hole in the work-top Take special care when fitting the hob into the work-top. If the procedures are not carried out correctly, exactly as described, the hob may be damaged. Before fitting the hob, remove the pan stands (if fitted) and the burners from the hob. When fitting the hob, first rest the surround entirely on the back edge of the hole in the work-top. Do not apply leverage to the surround; since this part is very delicate there is a risk of damaging it. Then lower the front of the hob until the appliance is completely in place. 8 Instructions for the Installer 5. Refer to page 12 for the relevant burner pressure and appropriate injector sizes. When the appliance is to be connected to Natural Gas then the pressure regulator supplied must be fitted to the gas inlet. A test point (for checking the gas pressure) is supplied either with the regulator or as a separate fitting in the case of ULPG (propane/butane) appliances. Connection of the appliance to the gas supply must be in accordance with the requirements of AS5601. For proper operation of a gas appliance it is essential for the air necessary for combustion of the gas to be able to flow naturally into the room. Air must flow directly into the room through openings in its outside walls. This (these) opening (s) must have a free passage cross-section of at least 100 cm2, or 200 cm2 for appliances not equipped with gas safety device. These openings must be constructed so that they cannot be obstructed indoors or outdoors, and should preferably be close to the floor on the side opposite to the combustion gas discharge point. If it is not possible to make the openings in the room where the cooker is installed, the necessary air may be taken from an adjoining room, proveded it is not a bedroom or a room with fire risk. 6. 3 Combustion gas discharge Combustion gases may be discharged by means of hoods connected to a flue with reliable natural draught, or a fan extraction system. An effective extraction system requires careful design by an authorised specialist, and must comply with the regulation distances and positions. After installation, the engineer must issue a certificate of compliance. 12 Instructions for the Installer 7. [. . . ] When properly positioned, the legs of the racks must not be suspended above the hob but should rest on top of it. Make sure that the pan stands are simply fitted over their burners, and are not left in a raised or tilted position; if this occurs, repeat the fitting procedure. WRONG RIGHT WRONG RIGHT 18 Instructions for the User After performing the operations described above (for each pan stand), the hob will be as shown below, with the feet of the pan stands forming a pattern of horizontal and vertical lines. If a pan wobbles noticeably, check that the pan stands have not been fitted incorrectly. 19 Instructions for the User 9. 2 Lighting burners with safety device The burner it controls is shown next to each knob (the example here shows the front left-hand burner). The appliance is equipped with electronic ignition. Simply press the knob and turn it anti-clockwise to the minimum flame symbol , until the burner lights. Keep the knob pressed down for about 2 seconds to keep the flame alight and prime the safety device. [. . . ]