User manual SMEG 6091BC

[. . . ] INSTALLATION MUST BE CARRIED OUT BY QUALIFIED STAFF IN COMPLIANCE WITH THE RELEVANT REGULATIONS. THIS APPLIANCE IS INTENDED FOR HOUSEHOLD USE AND COMPLIES WITH THE EEC DIRECTIVES CURRENTLY IN FORCE. THE APPLIANCE IS BUILT TO PROVIDE THE FOLLOWING FUNCTION: COOKING AND HEATING FOODS; ALL OTHER USES ARE TO BE CONSIDERED IMPROPER. THE MANUFACTURER DECLINES ALL LIABILITY FOR USES OTHER THAN THOSE STATED ABOVE. [. . . ] B). 24 Instructions for the Installer 2. 4 Fitting the hob into the hole in the work-top Take special care when fitting the hob into the work-top. If the procedures are not carried out correctly, exactly as described, the hob may be damaged. Before fitting the hob, remove the pan stands (if fitted) and the burners from the hob. When fitting the hob, first rest the surround entirely on the back edge of the hole in the work-top. Do not apply leverage to the surround; since this part is very delicate there is a risk of damaging it. Then lower the front of the hob until the appliance is completely in place. 25 Instructions for the Installer 3. Electrical connection Check that the power supply line voltage and size are as specified on the nameplate underneath the appliance's casing. This nameplate must never be removed. The plug on the end of the power supply lead and the wall socket must be of the same type and comply with the relevant regulations. Check that the power supply line is properly earthed. Pass the power supply cable through the rear of the cabinet, taking care that it does not touch the bottom case of the hob, or the oven (if any) built in underneath it. The appliance's power supply line must be fitted with an omnipolar breaking device with contact gap of at least 3 mm, located in an easily accessible position close to the appliance itself. The use of reductions, adapters or junctions is not recommended. If the power supply cable has to be replaced, the gauge of the wires in the new cable must be at least 0. 75 mm2 (3 x 0. 75 cable), bearing in mind that the earth wire (yellow-green) must be at least 20 mm longer at the end for connection to the appliance. Use only a type H05V2V2-F or similar cable resistant to a temperature of up to 90°C. The cable must be replaced by a qualified electrician, who must make the mains connection as shown below. To replace the nozzles and adjust the burners, the hob skin has to be removed. Proceed as described below. 5. 1 Removing the hob skin Remove all the burner components in the numerical order shown below: · · Pull off all the knobs. Lift all the burner components off the hob. 1 · Remove the cover plate of each burner by undoing the screws. 2 · Remove the hob fixing screws, taking only to remove screws shown on right. skin care the the 3 · After removing all the components described above, lift off the hob skin. 4 28 Instructions for the Installer 5. 2 Adjusting for bottled gas Undo the screw C and push the air regulator D fully down. Remove the nozzle E with a 7 mm spanner and fit the suitable one, following the instructions in the tables referring to the type of gas to be used. The nozzle must not be tightened with a torque of more than 3 Nm. Regulate the air flow by sliding the regulator D along until the distance "X" stated in point "5. 5 Adjusting the primary air flow" is obtained. Fix the regulator D by tightening the screw C. Rated heat capacity (kW) Nozzle diameter 1/100 mm Auxiliary Semi rapid Rapid Ultra Rapid 1. 05 1. 7 3. 0 5. 0 48 62 82 108 Burner Bottled gas ­ G30/G31 30/37 mbar By-pass mm 1/100 30 32 50 63 Reduced heat capacity (W) 400 450 1050 1600 Flow rate g/h G30 76 124 218 363 Flow rate g/h G31 75 121 214 357 5. 3 Adjusting for natural gas The appliance is tested with G20 (2H) natural gas at the pressure of 20 mbar. Clean their insides and change their lubricating grease. This operation must be carried out by a skilled technician. 31 Instructions for the User 6. Description of controls CONTROL AREA 6. 1 The front panel All the hob's control and monitoring devices are placed together on the front panel. 5 Burner Hob KNOB OPERATING MODE To light the flame, press the knob and at the same time turn it anti-clockwise to the minimum flame symbol . To adjust the flame, turn the knob to the zone between the maximum minimum settings. [. . . ] Use ordinary non-abrasive products for glass, with the aid of non-scratching sponges and wooden or plastic utensils if necessary. Rinse thoroughly and dry with a soft cloth or chamois leather. 7. 6 Cleaning instructiona for an acid-et ched glass hob 7. 6. 1 Grease Use washing up liquid and a microfibre cloth. 7. 6. 2 Rings and encrustations Use stainless steel cream or mildly abrasive creams; leave the product to act for a few minutes, then wipe away with a microfibre cloth. 7. 6. 3 Stubbom encrustations If using the microfibre cloth is not enough, a brass wire sponge can be used together with stainless steel cream or standard abrasive creams available in shops. [. . . ]