User manual SMEG A1CXU6

[. . . ] 12 5. 2 US installation and canadian installation / 4-wire branch circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 NOTE: THIS APPLIANCE MUST BE INSTALLED SOLELY AND EXCLUSIVELY BY A QUALIFIED TECHNICIAN. ANY TECHNICAL PROCEDURES MUST BE CARRIED OUT BY AN AUTHORIZED TECHNICIAN. INSTRUCTIONS FOR THE INSTALLER: these are intended for the qualified engineer who is able to install, commission and test the appliance 3 Important Safety Instruction 1. IMPORTANT SAFETY INSTRUCTIONS READ AND SAVE THESE INSTRUCTIONS ­ Your Safety And the Safety of Others Are Very Important. [. . . ] Separate the various waste materials and take them to the nearest special wastage collection centre. - - SAVE AND KEEP THIS BOOKLET 5 Instructions for the Installer 2. DIMENSIONAL REQUIREMENTS 1 24" (61 cm) min. when bottom of wood or metal cabinet is protected by not less than ¼ " (0. 64 cm) flame retard millboard covered with not less than No. 28 MSG sheet steel, 0. 015" (0. 4 mm) stainless steel, 0. 024" (0. 6 mm) aluminium or 0. 020" (0. 5 mm) copper. When installed in a 24" (61 cm) base cabinet with 25" (63. 5 cm) countertop ­ front of oven door protrudes 1-7/8" (4. 8) cm beyond 24" (61 cm) base cabinet. clearance between the to of the cooking platform and the bottom of an unprotected wood or metal cabinet; 2 13" (33 cm) max. upper cabinet depth; 3 35- ½ " (90 cm) min. cabinet opening widht; 4 18" (45. 7 cm) upper cabinet to countertop; 5 2" (5 cm) min. clearance from the sides of range to side wall or other combustible material; 6 Junction box. 6 Instructions for the Installer 2. 1 Product dimension Overall dimension: location of electrical connection points. A B C 12" 1/5 - 310 mm 7" - 180 mm 6" 3/4 - 170 mm Check location where the range will be installed. The range should be located for convenient use in the kitchen. NOTE: Observe all governing codes and ordinances. All openings in the wall or floor where range is to be installed must be sealed. Some cabinet and building materials are not designed to withstand the heat produced by the oven for baking. Check with your builder or cabinet supplier to make sure that the materials used will not discolor, delaminate or sustain other damages. Cabinet opening dimensions that are shown must be used. Given dimensions are minimum clearances. When installing a range under existing cabinets and the installation does not satisfy the minimum cabinet clearances, install a range hood above the cooktop to avoid burn hazards. 7 Instructions for the Installer 3. UNPACKING, MOVING AND PLACING THE RANGE CAUTION: This unit is design as a cooking appliance. Based on safety considerations, never use it for warming or heating a room. It is recommended that the grates, griddle plate and flame, burner caps, front kick panel and oven racks be removed to facilitate handling. This will reduce the weight for moving operations. [. . . ] Wire size and connections must conform to the requirements of the National Electrical Code, ANS/NFPA 70 ­ last edition (*) or CSA Standard C22. 1, Canadian Electrical code, Part 1 ­ Latest edition (**) and all local codes and ordinances for the kilowatt rating of the range. Copies of the standards listed may be obtained from: (*) National Fire Protection Association Batterymarch Park ­ Quincy, Massachusetts 02269; (**) CSA International 8501 East Pleasant Valley Road Cleveland, Ohio 44131-5575 . This appliance is manufactured with a yellow-green or green ground wire connected to the appliance chassis. After making sure that the power has been turned off connect the flexible connector. [. . . ]