User manual SMEG ALFA135V6

[. . . ] THE APPLIANCE MUST BE CONNECTED TO EARTH IN COMPLIANCE WITH ELECTRICAL SYSTEM SAFETY REGULATIONS. IF THE MAIN ELECTRICAL CONNECTION IS TO BE MADE BY MEANS OF A PLUG AND SOCKET, THEY MUST BOTH BE OF THE SAME TYPE AND MUST BE CONNECTED TO THE POWER SUPPLY LEAD IN ACCORDANCE WITH THE RELEVANT REGULATIONS. NEVER DISCONNECT THE PLUG BY PULLING ON THE CABLE. NEVER OBSTRUCT THE OPENINGS PROVIDED FOR VENTILATION OR HEAT DISPERSAL. IMMEDIATELY AFTER INSTALLATION, CARRY OUT A QUICK TEST ON THE OVEN FOLLOWING THE INSTRUCTIONS PROVIDED LATER IN THIS MANUAL. IF THE APPLIANCE FAILS TO OPERATE, DISCONNECT IT FROM THE ELECTRICAL MAINS AND CONTACT YOUR NEAREST SERVICE CENTRE. [. . . ] To set the current time, hold down START + STOP together until the display stops flashing. Now press or hold down START to increment the hour display. Once the current hour has been set, press STOP to set the minutes and increment them as before by pressing the START button. When the correct time is set, press the STOP button and the display will stop flashing. 4. 4 Setting the power After having set the time as described above and pressed the STOP button to confirm the setting, the display will show P8. 3 (maximum power absorption 8. 3 kW) if the oven is connected to a three-phase power supply, or P5. 5 (maximum power absorption 5. 5 kW) if the power supply is single-phase. Press START repeatedly to scroll through the power absorption settings available: P8. 3, P5. 5 or P3. 0 for three-phase power connection; P5. 5 or P3. 0 for single-phase power connection. After selecting the appropriate power, press STOP to confirm the setting. This power setting operation only has to be carried out the first time the oven is connected. The value set is saved and automatically used whenever the oven is switched on after this. To modify this setting or the 28 Instructions for the User time, press START + STOP together to return to the point described in section "4. 3 Setting the time". 4. 5 Program selection This oven has 15 different cooking programs, including: 14 user-editable programs for humidified fan-mode cooking (P1 to P14); 1 manual editable program for fan-mode cooking. The following table shows the parameters for each program. P1 P2 P3. . . . P14 P15 * Uprh preheating temperature Same as edited Ut°C Same as edited Ut°C Same as edited Ut°C Same as edited Ut°C Ut °C cooking temperature Preset 185°C Preset 190°C Editable Editable U Ct cooking time Preset 16` Preset 15' Editable Editable U Ht humidification time Editable if Ut°C > 150 Editable if Ut°C > 150 Editable if Ut°C > 150 N/A 4. 6 Humidified cooking The humidified fan-mode cooking programs the user is able to edit are from P1 to P14 A number of parameters can be edited for each program: · cooking temperature [U t°C]: User heating · cooking time [U Ct] : User cooking time · humidification cycles [U Ht]: User humidity time See cycle examples below 29 Instructions for the User To edit a humidified fan-mode program by entering the parameters exactly as required, turn the knob to one of the programs from P1 to P14. The display shows the parameters contained in the selected program. A beeper sounds to indicate that the editing mode has been accessed, and the message Ut°C appears on the display. Press START to display the cooking temperature. Press START or keep it pressed to increase the cooking temperature; each time START is pressed the temperature increments by 1°C (from 50° to 300°), or hold START down for increments of 5°C. humidification cycles [U Ht] can only be edited if Ut°C is set at a temperature above 150°C). Press STOP to move on to displaying the next parameter The display shows U Ct. Press START to display the cooking time. Press START or keep it pressed to increase the cooking time (from 1 min. Press STOP to move on to displaying the next parameter The display shows U Ht only if Ut°C is set > 150°C Press START to display the humidification cycles. Press START or keep it pressed to increase the number of humidification cycles (from 0 to 6 cycles where 0 means conventional fan-mode cooking without the aid of humidification). 30 Instructions for the User Press STOP to complete the program editing procedure. The parameters set are now saved in the chosen program. [. . . ] Use absorbent kitchen roll; remove stubborn dirt with a damp sponge and ordinary detergent. 35 Instructions for the User 6. EXTRAORDINARY MAINTENANCE Occasionally, the oven will require minor servicing procedures or the replacement of parts subject to wear and tear, such as gaskets, light bulbs, etc. The specific operations for each procedure of this kind are provided below. Before carrying out any operation, disconnect the oven from the electricity supply. 6. 1 Changing the light bulb Remove the protective cover A. Replace the bulb B with another of the same type. [. . . ]