User manual SMEG ALFA141VE

[. . . ] INSTRUCTIONS FOR SAFETY AND USE . . . . . . . . . . . . . . . . . . . . . . . 22 OVEN INSTALLATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 DESCRIPTION OF CONTROLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 USING THE OVEN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] These must be left free of any obstruction. Avoid crushing them. 26 Instructions for the User 3. DESCRIPTION OF CONTROLS START BUTTON This button lets you start cooking operations or perform a rapid cooling cycle when they are finished. In the steam model it starts the humidification cycle. STOP BUTTON This button lets you stop cooking at any time. DISPLAY This lets you display the selected program and related cooking parameters, as well as the operating power. PROGRAM SELECTION KNOB Allows you to set the cooking operation using one of the preset programs, to select the temperature and duration of the cooking operation as well as the operating power. 27 Instructions for the User 4. USING THE OVEN 4. 1 Warnings and general advice When using the oven for the first time, heat it up to its maximum temperature for a duration long enough to burn off any oily residues from the manufacturing process. To access food, always leave the door open as short a time as possible to prevent the temperature in the oven from falling and ruining the food. 4. 2 Setting the power When connecting the oven for the first time, the maximum power absorbed will appear flashing on the display. If the product is already connected, this will be in the "OFF" state. In both cases proceed as follows: · Press the "PUSH" knob for at least 3 seconds: the display will show the text "P8. 3" (equivalent to the maximum absorbed power of 8. 3 kW) if the oven connection is three phase, or "P5. 5" (equivalent to the maximum absorbed power of 5. 5 kW) if the oven connection is single phase. Turn the knob to the or symbols to move between the proposed power absorptions P8. 3, P5. 5 and P3. 0 (if the oven connection is three phase), or P5. 5 and p3. 0 (if the oven connection is single phase). Once you have selected the power, press the "PUSH" button to confirm the selection. · · The power setting operation must be performed the first time that the oven is connected. The value set is stored and used automatically whenever the oven is used subsequently. 28 Instructions for the User 4. 3 Choice of programs This appliance allows you select 40 cooking programs including: · · · 38 programs that can be edited and saved as the user wishes 1 manual program "P40" 1 preheating program with delayed start "P39" 4. 4 Humidified cooking operations (only in the steam model) The humidified programs that the user can modify are included between P01 and P40 apart from program P39. For each program it is possible to increase the number of the humidification cycles from 0 to 10 (where 0 corresponds to traditional cooking without using humidification). Humidification cycles can be modified only if an oven temperature higher than 150°C is set. Water can be allowed to flow inside the cooking chamber only during cooking, by controlling the relevant inlet valve manually. To do this, just keep the "START" button pressed for at least one second. Releasing the button stops the water from flowing in. The diagram below represents an example of cooking with 5 humidification cycles. 29 Instructions for the User 4. 5 Editing / saving a program The oven has 38 programs that can be modified by the user (from P01 to P38). To set the operational parameters of a program: · · · · · · Turn the knob to the or symbols to select the program you wish to save / edit. Keep the "PUSH" knob pressed for 3 seconds: the display will show the cooking temperature. Turn the knob to the or symbols to set the cooking temperature. Press the "PUSH" knob: the display will show the cooking time. Turn the knob to the or symbols to set the cooking time (from 1 to 99 min). [. . . ] The text "PEnd" appears on the display and after 3 seconds it will display P39, the temperature and the pre-heating start time in succession. To start the program press the "START" button for at least 2 seconds. The display will show the current time and "P39A" in succession until the program is activated at the set time. · The oven will perform preheating at the set time; during this phase the display shows "P39", the text "InF" and the set temperature in succession; this will continue until interrupted by the "STOP" button. The program must be activated every day. [. . . ]