User manual SMEG ALFA200XE

[. . . ] 6. PRECAUTIONS FOR SAFETY AND USE _____________________ 21 INSTALLING THE OVEN __________________________________ 23 DESCRIPTION OF CONTROLS ____________________________ 25 USING THE OVEN _______________________________________ 26 CLEANING AND MAINTENANCE ___________________________ 33 EXTRAORDINARY MAINTENANCE _________________________ 36 INSTRUCTIONS FOR THE INSTALLER: these are intended for the qualified engineer who is to install, commission and test the appliance. INSTRUCTIONS FOR THE USER: these provide recommendations for use, a description of the controls and the correct procedures for cleaning and maintaining the appliance. 20 Presentation 1. PRECAUTIONS FOR SAFETY AND USE THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE. TAKE GOOD CARE OF IT AND KEEP IT TO HAND THROUGHOUT THE OVEN'S LIFE CYCLE. WE URGE YOU TO READ THIS MANUAL AND ALL THE INFORMATION IT CONTAINS CAREFULLY BEFORE USING THE OVEN. [. . . ] To set the current time, hold down START + STOP together until the display stops flashing. Now press START to increment the hour display. Once the current hour has been set, press STOP to set the minutes and increment them as before by pressing the START button. When the correct time is set, press the STOP button and the display will stop flashing. 4. 5 Setting the power After having set the time as described above and pressed the STOP button to confirm the setting, the display will show P8. 3 (maximum power absorption 8. 3 kW) if the oven is connected to a three-phase power supply, or P5. 5 (maximum power absorption 5. 5 kW) if the power supply is single-phase. Press START repeatedly to scroll through the power absorption settings available: P8. 3, P5. 5 or P3. 0 for three-phase power connection; 26 Instructions for the User P5. 5 or P3. 0 for single-phase power connection. After selecting the appropriate power, press STOP to confirm the setting. This power setting operation only has to be carried out the first time the oven is connected. The value set is saved and automatically used whenever the oven is switched on after this. To modify this setting or the time, press START + STOP together to return to the point described in section "4. 3 Setting the time". 4. 6 Program selection This oven has 15 different cooking programs, including: 14 user-editable programs for humidified fan-mode cooking (P1 to P14); 1 manual editable program for fan-mode cooking. The following table shows the parameters for each program. P1 P2 P3. . . P14 Uprh preheating temperature Same as edited Ut°C Same as edited Ut°C Same as edited Ut°C Same as edited Ut°C Ut °C cooking temperature Preset 185°C Preset 190°C Editable Editable U Ct cooking time Preset 16' Preset 15' Editable Editable U Ht humidification time Editable Editable Editable N/A 4. 7 Humidified cooking The humidified fan-mode cooking programs the user is able to edit are from P1 to P14 A number of parameters can be edited for each program: · cooking temperature [U t°C]: User heating · cooking time [U Ct] : User cooking time · humidification cycles [U Ht]: User humidity time See cycle examples below 27 Instructions for the User To edit a humidified fan-mode program by entering the parameters exactly as required, turn the knob to one of the programs from P1 to P14. The display shows the parameters contained in the selected program. A beeper sounds to indicate that the editing mode has been accessed, and the message Ut°C appears on the display. Press START to display the cooking temperature. Press START or keep it pressed to increase the cooking temperature; each time START is pressed the temperature increments by 1°C (from 50° to 300°), or hold START down for increments of 5°C. humidification cycles [U Ht] can only be edited if Ut°C is set at a temperature above 150°C). Press STOP to move on to displaying the next parameter The display shows U Ct. Press START to display the cooking time. Press START or keep it pressed to increase the cooking time (from 1 min. Press STOP to move on to displaying the next parameter The display shows U Ht only if Ut°C is set > 150°C Press START to display the humidification cycles. Press START or keep it pressed to increase the number of humidification cycles (from 0 to 6 cycles where 0 means conventional fan-mode cooking without the aid of humidification). Press STOP to complete the program editing procedure. 28 Instructions for the User The display shows UEnd. [. . . ] Release STOP and preheating will start automatically after 5 seconds; the oven will preheat to the set cooking temperature. ­ When the cooking process is over, to repeat the same program do not turn the knob and press START again. 4. 11 Rapid cooling The oven has a special function which allows its interior to be cooled quickly. To activate this function, turn the function selector to "0", open the door and press the START key for at least 2 seconds. The fans inside the oven will come into operation with the heating elements off. [. . . ]