User manual SMEG ALFA 341

[. . . ] INSTRUCTIONS FOR USE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 SAFETY PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 ENVIRONMENTAL CARE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 DESCRIPTION OF CONTROLS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] If the product is already connected, this will be in the "OFF" status. In both cases proceed as follows: ALFA341 · · Turn the knob towards the symbol or to select the maximum power absorbed by the oven between P15 (15 kW) and P9 (9 kW). Once you have selected the power, press the "PUSH" knob to confirm the selection. ALFA241 · · Turn the knob towards the symbol or to select the maximum power absorbed by the oven between P8. 3 (8. 3 kW) and P5. 5 (5. 5 kW). Once you have selected the power, press the "PUSH" knob to confirm the selection. The power setting operation must be performed the first time that the oven is connected. The value set is stored and used automatically whenever the oven is used subsequently. If the product is already connected and you want to modify the absorbed power setting, from "OFF" status, hold down the "PUSH" knob for at least 3 seconds. 5. 3 Choice of programs This appliance allows you to select 40 cooking programs including: · 38 programs that can be edited and saved as the user wishes; · 1 preheating program with delayed start "P39"; · 1 manual program "P40". 33 Instructions for the user 5. 4 Humidified cooking (on some models only) The humidified programs that the user can modify are included between P01 and P40 apart from program P39. 3 different humidity levels can be set for each program: H1 (low), H2 (medium) and H3 (high). Each set level has different intervals between the steam injection cycles: 8' pause for H1, 5' for H2 and 2' for H3. Humidification cycles can be set and modified only if an oven temperature higher than 110°C is selected. The oven chamber can be humidified during cooking by controlling the relevant inlet valve: To do this, just keep the "START" button pressed for at least one second. Releasing the button stops the water from flowing in. The display will show the set parameters in sequence, with the time remaining until the end of cooking and the program selected. It is possible to start cooking early before the preheating temperature is reached, by keeping the "START" button pressed for 3 seconds. During the last minute of cooking, only the countdown of the remaining 60 seconds will be displayed. At the end, a beep and the text "End" flashing (for 20 minutes) will indicate that cooking has been completed. To return to the "OFF" status keep the "STOP" button pressed for 4 seconds. 2 3 4 5 6 During cooking, if it is necessary to open the oven door, the display shows the message "door" together with a continuous acoustic signal. When the door is closed the oven will continue cooking. 36 Instructions for the user 5. 6. 1 Extending a cooking operation When a cooking operation finishes, it is possible to extend it manually: 1 While the display is showing the text "End", press the "START" button; the text "tP00" will appear on the display. 2 3 4 Turn the knob to the or symbol to set the additional minutes of cooking; at most 20 extra minutes are allowed. To start cooking with the extra time that has just been set, press the "START" button for at least 2 seconds. At the end of cooking, the text "End" will continue to flash for the next 20 minutes and the oven light will remain on. 5. 6. 2 Modifying a program during cooking The program can be modified during cooking: 1 Press the "PUSH" knob: the display will show the cooking temperature. 2 Modify the settings as described in points 3 - 10 of paragraph "5. 5 Editing / saving a program". Changes made to the program during cooking are not saved. 3 3 seconds after the last change, the program automatically quits the modification status and saves the settings (as described in this paragraph, the modified parameters are saved solely until the end of cooking). 37 Instructions for the user 5. 7 Manual cooking The manual program is "P40" and can be edited by the user, but does not save the cooking parameters. [. . . ] The distance from the rear wall must allow easy access to the terminal board for connection of the power supply cable. Installation must be carried out by a qualified technician and in compliance with the EEC DIRECTIVES currently in force. 8. 1 Electrical connection Make sure the voltage and the cross-section of the power supply line match the specifications indicated on the identification plate positioned on the side of the oven. Do not remove this plate for any reason. ALFA241 For operation on 380-415V 3N~: use a H07RNF type five-core cable (5 x 1. 5 mm²). ALFA341 For operation on 380-415V 3N~: use a H07RNF type five-core cable (5 x 4 mm²). When linking up to the power supply network by plug and socket, the connection must be completed with a plug of adequate capacity. [. . . ]