User manual SMEG APP490X-8

[. . . ] INSTRUCTIONS FOR USE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 SAFETY PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 ENVIRONMENTAL RESPONSIBILITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 GET TO KNOW YOUR OVEN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] starts flashing and PT1 can be will turned to change the set duration. A few seconds after the last change, stop flashing, and semi-automatic cooking will restart from the new value. To change the preset temperature, wait for to become steady and turn PT1 to the right or left to increase or decrease the cooking temperature. 62 Instructions for the user 7. 7. 3 Automatic cooking Automatic cooking is the function which allows a cooking operation to be started at a set time and then ended after a specific length of time set by the user. Select a cooking function, set the desired cooking temperature or leave the preset temperature (see "7. 6 Selecting functions (pyrolytic models)") and press PT1 twice. The display will show and (flashing). Turn PT1 to the right or left to set the minutes of cooking (from 00:01 to 23:59). For reasons of safety, when setting automatic cooking the user must first program a cooking duration and then set the cooking start time. It is not possible to set the cooking start time only, without setting the cooking duration. After setting the duration, press PT1 once. and the current time will appear on the display. Turning PT1 to the right increases the time, allowing the cooking start time to be set. A few seconds after the desired duration is set, and will stop flashing and remain constantly on, and the oven will start to wait for the starting time set. At the end, the word STOP will appear on DSP1, cooking will stop and a buzzer will sound; press PT1 once to deactivate it. If you wish to continue cooking beyond the set time, press PT1 again. The oven will restart normal operation with the cooking settings selected previously. To switch the oven off completely, PT2 must be turned to 0. 63 Instructions for the user Modifying the set data Once automatic cooking has started, its duration can be changed. When and are steady and cooking is in progress, or the oven is in starts flashing and standby waiting for cooking to start, press PT1 once. PT1 can be turned to change the set duration. Press PT1 again; goes out, starts to flash, and the cooking start time will be displayed on DSP1. The cooking start time can be increased or decreased by turning PT1. A few seconds after the last change, and will appear (in steady mode) on DSP1 and automatic cooking will restart with the new settings. Once the desired function has been selected, the oven will begin cooking at the preset temperature. Cooking is preceded by a pre-heating phase (common to all functions) which allows the oven to reach the cooking temperature more quickly. [. . . ] Remove the middle pane by lifting it upwards. Cleaning: · Now it is possible to clean the external glass panel and the panels removed previously. In the case of stubborn dirt, wash with a damp sponge and neutral detergent. Replacing the glass panels: · Replace the panes in the opposite order to which they were removed. · Reposition the internal glass panel, taking care to centre and insert the 4 pins attached to the glass into their slots in the oven door by applying a slight pressure. 82 Instructions for the installer 11. INSTALLING THE APPLIANCE 11. 1 Electrical connection The identification plate bearing the technical data, serial number and brand name is visibly positioned on the appliance. [. . . ]