User manual SMEG BL3

[. . . ] INSTRUCTION MANUAL DISHWASHER Contents 1. Safety and operating instructions __________________________ 26 2. Installation and hook-up _________________________________ 28 2. 1 Water supply connection _____________________________________________________ 28 2. 2 Electrical connection ________________________________________________________ 29 3. Description of the controls _______________________________ 30 3. 1 Upper panel _______________________________________________________________ 30 3. 2 Information display__________________________________________________________ 30 3. 3 Washing programs__________________________________________________________ 31 4. [. . . ] In this way, the excess saline solution will be immediately removed by the water; the prolonged presence of salt water inside the tank may lead to corrosion. · · · Be careful not to confuse the salt and detergent packages; adding detergent to the salt container will damage the water softening system. ADJUSTING THE WATER SOFTENING SYSTEM The dishwasher is equipped with an electronic device for adjusting the water softening setting according to the hardness of the water. Depending on model, the setting may be made electronically or by means of a selector switch. 34 User instructions ELECTRONIC SETTING The value entered for this parameter establishes whether or not regeneration is to be carried out at the end of the washing cycle, on the basis of the table below. SETTING 0 1 2 3 4 5 WATER HARDNESS < 9°dH (15°dF) < 15°dH (25°dF) < 23°dH (40°dF) < 34°dH (60°dF) < 46°dH (80°dF) < 58°dH (100°dF) REGENERATION Not performed Performed every 5 cycles Performed every 4 cycles Performed every 3 cycles Performed every 2 cycles Performed every cycle Contact your local water board for information on the hardness of your water supply. Programming procedure: Press the PROGRAM SELECTION (2) and DELAYED START (3) buttons simultaneously for · 3 seconds until the DISPLAY (7) shows the symbol "H"; Press the DELAYED START button (3) to modify the parameter; · Press the PROGRAM SELECTION button (2) to exit from the procedure. · SWITCH SETTING According to the machine model, the selector which acts on the adjustment may be located: inside the plastic locking ring located on the right-hand side, inside the dishwasher; · inside the water softener, just below the cap. · Both allow for adjustment to 5 settings: 35 User instructions WATER HARDNESS TABLE WATER HARDNESS German Degrees (°dH) French Degrees (°dF) 0510 18 27 36 4 9 17 26 35 47 0-7 8 - 15 16 - 30 31 - 45 46 - 60 61 - 80 SETTING Setting N. 5 Contact your local water board for information on the hardness of your water supply. 4. 2 Using the rinse aid and detergent dispensers The detergent and rinse aid dispensers are situated on the inner part of the door: the detergent dispenser is on the left, and the rinse aid dispenser is on the right. With the exception of the SOAK program, before every washing cycle it is necessary to add the required amount of detergent to the detergent dispenser. The rinse aid, on the other hand, should only be added as required. ADDING THE RINSE AID The rinse aid helps the dishes dry faster and prevents the formation of scale deposits and staining; it is automatically added to the water during the final rinse cycle, from the container situated on the inner side of the door. · · · · · Open the door. Rotate the container cap anticlockwise by 1/4 of a turn and remove it. Add the rinse aid until the container is full (approximately 140 cc). The optical level indicator on the side of the cap should be completely obscured. Refill the rinse aid when the optical level indicator becomes clear again, or when the rinse aid warning light illuminates. Replace the cover and turn it in a clockwise direction. Use a cloth to remove any spillage of rinse aid which might lead to the formation of excess foam. ADJUSTING THE RINSE AID DISPENSER SETTING The dishwasher is factory set for medium water hardness. However it possible to change the setting by turning the dispenser's selector to the desired position: the amount of rinse aid dispensed is proportional to the selector position. The setting must be increased when the washed dishes appear dull or have circular staining. · · · To adjust the rinse aid setting, rotate the dispenser cap through a quarter turn in an anticlockwise direction and remove it. Then use a screwdriver to rotate the rinse aid selector to the desired position. Replace the cap, turning it clockwise. 36 User instructions · · The amount of rinse aid must be increased if the washed dishes appear dull or feature circular stains. If, on the other hand, the dishes are sticky or have white streaks, it is necessary to reduce the rinse aid setting. ADDING THE DETERGENT To open the detergent dispenser cap, lightly press the button P. Add the detergent and close the cap carefully. During the washing cycle, the dispenser will be opened automatically. · When a SUPER program is selected, in addition to the normal dose of detergent, it is necessary to add an additional amount inside compartment G or H. Use only detergents specially formulated for dishwashers. [. . . ] Ce bloc de lavage est doté d'un dispositif qui permet de régler la planéité de l'appareil après sa mise en place. L'extraire complètement et le lever vers le haut comme un tiroir normal (Fig. 1) ; Enlever le socle inférieur en l'extrayant vers le haut puis vers l'extérieur (Fig. 2) ; Avec une clé à douille de 10, tourner les écrous hexagonaux, illustrés dans la figure cicontre, jusqu'à obtenir la planéité par rapport au sol (Fig. 3) ; Remonter le socle en ayant soin d'enfiler d'abord les deux vis en bas; l'encastrer ensuite avec les deux en haut (Fig. 4). 1. 4. Diese Wascheinheit verfügt über eine Einrichtung für die waagrechte Ausrichtung des Geräts nach dem Aufstellen. Die untere rechte Schublade herausnehmen. [. . . ]