User manual SMEG C6GVXBE

[. . . ] INSTRUCTIONS FOR USE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . INSTRUCTIONS FOR DISPOSAL ­ OUR ENVIRONMENTAL CARE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . INSTALLING THE APPLIANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79 3. 1 Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Check for any leaks using a soapy solution, never with a flame. For the connection between the cooker and the gas cylinder use a portion of standards-compliant hose not less than 1. 4 m in length. 82 Instructions for the installer 4. ADAPTATION TO DIFFERENT TYPES OF GAS Before carrying out the following operations, disconnect the appliance from the electricity supply. The appliance is preset for natural gas G20/25 at a pressure of 20/25 mbar. In the case of operation with other types of gas the burner nozzles must be changed and the minimum flame adjusted on the gas taps. To change the nozzles, proceed as described in the following paragraphs. 4. 1 Replacement of nozzles on the cooking hob 1 Extract the pan stands and remove all the caps and flame-spreader crowns; 2 Unscrew the burner nozzles with a 7 mm socket wrench; 3 Replace the burners in the correct positions. 83 Instructions for the installer 4. 2 Burner and nozzle characteristics table (60 cm model); Burner Rated heating capacity (kW) Nozzle diameter 1/ 100 mm 50 65 100 87 LIQUID GAS ­ G30/G31 28/37 mbar By-pass Reduced Capacity 1/100 capacity g/h G30 mm (W) 30 400 73 33 500 127 65 1600 290 50 900 233 NATURAL GAS ­ G20/G25 20/25 mbar Nozzle diameter 1/100 mm 72 (X) 97 (Z) 135 (K) 130 Reduced capacity (W) 400 500 1600 900 Capacity g/h G31 71 125 286 229 Auxiliary Semi rapid Ultra-rapid Oven Burner 1. 0 1. 8 4. 0 3. 2 Rated heating capacity (kW) Auxiliary Semi rapid Ultra-rapid Oven 1. 0 1. 8 4. 0 3. 2 84 Instructions for the installer 4. 3 Burner and nozzle characteristics table (90 cm model); Burner Rated heating capacity (kW) Nozzle diameter 1/ 100 mm 50 65 85 100 110 LIQUID GAS ­ G30/G31 28/37 mbar By-pass Reduced Capacity 1/100 capacity g/h G30 mm (W) 30 400 73 33 500 127 45 800 218 65 1600 291 59 1300 378 NATURAL GAS ­ G20/G25 20/25 mbar Nozzle diameter 1/100 mm 72 97 115 135 164 Reduced capacity (W) 400 500 800 1500 1300 Capacity g/h G31 71 125 214 286 371 Auxiliary Semi rapid Rapid Ultra-rapid Maxi oven Burner 1. 0 1. 8 3. 0 4. 0 5. 2 Rated heating capacity (kW) Auxiliary Semi rapid Rapid Ultra-rapid Maxi oven 1. 0 1. 8 3. 0 4. 0 5. 2 85 Instructions for the installer 4. 4 Arrangement of the burners on the cooking hob BURNERS 1. Ultra-rapid 4. 5 Oven burner adjustment (only for models with a gas oven) To adjust the oven burner you need to open the oven door and carry out the following operations: · Remove the oven basin and its rack. · Lift up the oven surface and pull it outwards. 4. 5. 1 Replacing the oven burner nozzle · Loosen the oven burner fixing screw A. · Push the burner B towards the right until the nozzle is accessible. · Using a 13 socket spanner replace the nozzle, inserting a new nozzle suitable for the type of gas to be used (see paragraph "4. 2 / 4. 3 Burner and nozzle characteristics table"). 4. 5. 2 Primary air adjustment for the oven burner · Loosen the adjustment screw "A" of the air regulation sleeve. · Turn the adjustment sleeve "B" to the position that corresponds to the type of gas to be used according to the table below. · Tighten the adjustment screw and restore the seals. · When the operation is completed, reassemble the burner correctly. X= NATURAL GAS 5 mm G 30/31 (LPG) 10 mm 86 Instructions for the installer 5. FINAL OPERATIONS After replacing the nozzles, reposition the flame-spreader crowns, the burner caps and the pan stands. Following adjustment to a gas other than the preset one, replace the gas adjustment label fixed to the appliance with the one corresponding to the new gas. The label is inserted inside the pack together with the nozzles. 5. 1 Regulation of the hob burners minimum for natural gas Light the burner and turn it to the minimum position . Extract the gas tap knob and turn the adjustment screw at the side of the tap rod until the correct minimum flame is achieved. Refit the knob and verify that the burner flame is stable (turning the knob rapidly from the maximum to the minimum position the flame must not go out). Repeat the operation on all the gas taps. For models with valves, keep the knob at minimum level for a few seconds to keep the flame lit and to activate the safety device. 5. 2 Regulation of the hob burners minimum for liquid gas In order to adjust the minimum with liquid gas, the screw at the side of the tap rod must be tightened clockwise all the way. The bypass diameters for each individual burner are shown in paragraph "4. 2 Burner and nozzle characteristics table (60 cm model);". When the adjustment is completed, restore the sealing of the bypasses with paint or other material. 5. 3 Positioning and levelling the appliance (depending on the model) After making the electrical and gas connections, level the appliance on the floor by means of its four adjustable feet. [. . . ] This is a completely natural phenomenon which has no effect on the operation of this component. Warning: If using cast iron pan stands (optional not supplied), at the end of cooking using pans with aluminium bases, you may find white residues on the pan stands. These residues are usually caused by the pan base rubbing against the pan stand and are difficult to remove with normal cleaning. Using abrasive or excessively aggressive products to clean the pan stand could damage its enamel surface. 96 Instructions for the user 10. 2. 2 Burner caps and flame spreader crowns For easier cleaning, the caps and the flame spreader crowns can be removed; wash them with warm water and a non-abrasive detergent making sure to remove any encrustation and wait until they are perfectly dry. [. . . ]