User manual SMEG C6GVXI

[. . . ] INSTRUCTIONS FOR USE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . INSTRUCTIONS FOR DISPOSAL ­ OUR ENVIRONMENTAL CARE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . INSTALLING THE APPLIANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76 3. 1 Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Screw the end of the flexible hose L, with the seal C positioned between the B threaded ½" external gas connector (ISO 228-1). At the end of the installation, check for any leaks with a soapy solution, never with a flame. 3. 4. 5 Connection to the gas cylinder in the internal compartment of the appliance Open the side compartment and insert a gas cylinder of max 15 kg. Push one end of the hose onto the hose connector and secure it with one of the two supplied clamps. Insert the hose into the gas cylinder compartment via the hole located at the back of the appliance following the diagram shown to the side. Push the other end onto the pressure regulator of the gas cylinder; secure it in place using the second supplied clamp. Check for any leaks using a soapy solution, never with a flame. For the connection between the cooker and the gas cylinder use a portion of standards-compliant hose not less than 1. 4 m in length. 79 Instructions for the installer 4. ADAPTATION TO DIFFERENT TYPES OF GAS Before carrying out the following operations, disconnect the appliance from the electricity supply. The appliance is preset for natural gas G20 (2H) at a pressure of 20 mbar. In the case of operation with other types of gas the burner nozzles must be changed and the minimum flame adjusted on the gas taps. To change the nozzles, proceed as described in the following paragraphs. 4. 1 Replacement of nozzles on the cooking hob 1 Extract the pan stands and remove all the caps and flame-spreader crowns; 2 Unscrew the burner nozzles with a 7 mm socket wrench; 3 Replace the burner nozzles according to the type of gas to be used (see paragraph "4. 2 Burner and nozzle characteristics table (60/70 cm. 4 Replace the burners in the correct positions. The nozzles for using town gas (G110 ­ 8 mbar) are available from authorised service centres. 80 Instructions for the installer 4. 2 Burner and nozzle characteristics table (60/70 cm. model); Burner Rated heating capacity (kW) Nozzle diameter 1/ 100 mm 50 65 100 87 LIQUID GAS ­ G30/G31 28/37 mbar By-pass Reduced Capacity 1/100 capacity g/h G30 mm (W) 30 400 76 33 500 131 65 1600 290 50 900 233 TOWN GAS ­ G110 8 mbar Nozzle diameter 1/100 mm 145 (/8) 185 (/2) 350 (/13) 270 Reduced capacity (W) 400 500 1200 900 Capacity g/h G31 75 129 286 229 Auxiliary Semi rapid Ultra-rapid Oven Burner 1. 05 1. 8 4. 0 3. 2 Rated heating capacity (kW) Auxiliary Semi rapid Ultra-rapid Oven 1. 05 1. 8 4. 0 3. 2 The nozzles and data concerning TOWN GAS are available at the Authorised Service Centres. Burner Rated heating capacity (kW) NATURAL GAS ­ G20/G25 20/25 mbar Nozzle diameter 1/100 mm 72 (X) 97 (Z) 135 (K) 130 Reduced capacity (W) 400 500 1600 900 Auxiliary Semi rapid Ultra-rapid Oven 1. 05 1. 8 4. 0 3. 2 81 Instructions for the installer 4. 3 Burner and nozzle characteristics table (80/90 cm. model); Burner Rated heating capacity (kW) Nozzle diameter 1/ 100 mm 50 65 85 100 106* / 110** LIQUID GAS ­ G30/G31 28/37 mbar By-pass Reduced Capacity 1/100 capacity g/h G30 mm (W) 30 400 76 33 500 131 45 800 218 65 1600 291 62 1300 378 TOWN GAS ­ G110 8 mbar Nozzle diameter 1/100 mm 145 (/8) 185 (/2) 260 (/3) 350 (/13) Reduced capacity (W) 400 500 800 1200 Capacity g/h G31 75 129 214 286 371 Auxiliary Semi rapid Rapid Ultra-rapid Maxi oven Burner 1. 05 1. 8 3. 0 4. 0 4. 6* / 5. 2** Rated heating capacity (kW) Auxiliary Semi rapid Rapid Ultra-rapid 1. 05 1. 8 3. 0 4. 0 The nozzles and data concerning TOWN GAS are available at the Authorised Service Centres. Burner Rated heating capacity (kW) NATURAL GAS ­ G20/G25 20/25 mbar Nozzle diameter 1/100 mm 72 97 115 135 155* / 164** Reduced capacity (W) 400 500 800 1500 1300 Auxiliary Semi rapid Rapid Ultra-rapid Maxi oven 1. 05 1. 8 3. 0 4. 0 4. 6* / 5. 2** * 80 cm oven / ** 90 cm oven 82 Instructions for the installer 4. 4 Arrangement of the burners on the cooking hob (Mod. Ultra-rapid 4. 5 Arrangement of the burners on the cooking hob (Mod. Ultra-rapid 4. 6 Arrangement of the burners on the cooking hob (Mod. Ultra-rapid 4. 7 Oven burner adjustment (only for models with a gas oven) To adjust the oven burner you need to open the oven door and carry out the following operations: · Remove the oven basin and its rack. · Lift up the oven surface and pull it outwards. 4. 7. 1 Replacing the oven burner nozzle · Loosen the oven burner fixing screw A. · Push the burner B towards the right until the nozzle is accessible. · Using a 13 socket spanner replace the nozzle, inserting a new nozzle suitable for the type of gas to be used (see paragraph "3. 2/3. 3 Burner and nozzle characteristics table"). 83 Instructions for the installer 4. 7. 2 Primary air adjustment for the oven burner · Loosen the adjustment screw "A" of the air regulation sleeve. [. . . ] This is a completely natural phenomenon which has no effect on the operation of this component. Warning: If using cast iron pan stands (optional not supplied), at the end of cooking using pans with aluminium bases, you may find white residues on the pan stands. These residues are usually caused by the pan base rubbing against the pan stand and are difficult to remove with normal cleaning. Using abrasive or excessively aggressive products to clean the pan stand could damage its enamel surface. 92 Instructions for the user 10. 2. 2 Burner caps and flame spreader crowns For easier cleaning, the caps and the flame spreader crowns can be removed; wash them with warm water and a non-abrasive detergent making sure to remove any encrustation and wait until they are perfectly dry. [. . . ]