User manual SMEG C8GGXK

[. . . ] INSTRUCTIONS FOR USE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . INSTRUCTIONS FOR DISPOSAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2. 1 Our environmental responsibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2. 2 Your environmental responsibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] 4 Replace the burners in the correct position. 10 Instructions for the installer 5. 2 Burner and nozzle characteristics table Burner Rated heating capacity (kW) Nozzle diameter 1/100 mm 50 65 100 106 95 LIQUID GAS ­ G30/G31 30/37 mbar Reduced capacity (W) 350 450 1500 1300 Rated g/h G30 76 131 284 334 269 Rated g/h G31 75 129 279 329 264 Auxiliary Semi-rapid Ultra-rapid Oven Grill 1. 05 1. 8 3. 9 4. 6 3. 7 Rated heating capacity (kW) Burner NATURAL GAS ­ G20 20 mbar Nozzle diameter 1/100 mm 72 (X) 97 (Z) 135 (K) 155 145 Reduced capacity (W) 350 450 1500 1300 - Auxiliary Semi-rapid Ultra-rapid Oven Grill 1. 05 1. 8 3. 9 4. 6 3. 7 11 Instructions for the installer 5. 3 Arrangement of the burners on the hob BURNERS 1. Ultra-rapid 5. 4 Adjustment of oven burner To adjust the oven burner you need to open the oven door and carry out the following operations: · Remove the oven basin and its rack. · Lift up the oven surface and pull it outwards. 5. 4. 1 Replacing the oven burner nozzle · Loosen the oven burner fixing screw A. · Push burner B towards the right until the nozzle is accessible. · Using a 13 socket wrench, replace the nozzle, inserting a new nozzle suitable for the type of gas to be used (see paragraph "5. 2 Burner and nozzle characteristics table"). 5. 4. 2 Primary air adjustment for the oven burner · Loosen adjustment screw "A" of the air regulation sleeve. · Turn adjustment sleeve "B" to the position that corresponds to the type of gas to be used according to the table below. · Tighten the adjustment screw and restore the seals. · When the operation is completed, reassemble the burner correctly. Oven Grill X= X= NATURAL GAS 5 mm 5 mm G 30/31 (LPG) 10 mm 15 mm 12 Instructions for the installer 6. FINAL OPERATIONS After replacing the nozzles, reposition the flame-spreader crowns, the burner caps and the racks. Following adjustment to a gas other than the preset one, replace the gas setting label fixed to the appliance with the one corresponding to the new gas. The label is inserted inside the pack together with the nozzles. 6. 1 Regulation of the hob burner minimum for natural gas Light the burner and turn it to the minimum position . Extract the gas tap knob and turn the adjustment screw at the side of the tap rod until the correct minimum flame is achieved. Refit the knob and verify that the burner flame is stable (when turning the knob rapidly from the maximum to the minimum position the flame must not go out). Repeat the operation on all the gas taps. For valved models, keep the knob pressed in at the minimum level for a few seconds to keep the flame lit and to activate the safety device. 6. 2 Adjusting the hob burner minimum for liquid gas In order to adjust the minimum setting with liquid gas, the screw at the side of the tap rod must be tightened clockwise all the way. The bypass diameters for each individual burner are shown in paragraph "5. 2 Burner and nozzle characteristics table". When the adjustment is completed, restore the sealing of the by-passes with paint or another material. 6. 3 Positioning and levelling the appliance (depending on the model) After making the electrical and gas connections, level the appliance on the floor by means of its four adjustable feet. For good cooking results, the appliance must be properly levelled. Depending on the model you have purchased, the feet height adjustment may vary from 70 to 95 mm and from 110 to 160 mm. These heights refer to the distance between the highest point of the foot (fixed part) and the lowest point (movable part which rests on the floor). 6. 4 Adjustment of the oven burner minimum Light the burner and turn it to the minimum position . Extract the gas tap knob and turn the adjustment screw at the side of the tap rod until the correct minimum flame is achieved. [. . . ] These residues are usually caused by the pan base rubbing against the rack and are difficult to remove with normal cleaning. Using abrasive or excessively aggressive products to clean the pan stand could damage its enamel surface. 21 Instructions for the user 11. 2. 2 Burner caps and flame-spreader crowns For easier cleaning, the caps and the flame-spreader crowns can be removed; wash them with warm water and a non-abrasive detergent, making sure to remove any encrustation, and wait until they are perfectly dry. WARNING: never wash these parts in a dishwasher. They can be left to soak in warm water and detergent. [. . . ]