User manual SMEG C9GGSSA

[. . . ] INSTRUCTIONS FOR USE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . INSTRUCTIONS FOR DISPOSAL ­ OUR CONCERN FOR THE ENVIRONMENT . . . . . . . . . . . . . . . INSTALLING THE APPLIANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 3. 1 Wall fixing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] · Tighten the adjustment screw and restore the seals. · When the operation is completed, reassemble the burner correctly. OVEN X= NATURAL GAS 5 mm NATURAL GAS 5 mm G 30/31 (LPG) 10 mm G 30/31 (LPG) 10 mm 13 GRILL X= Instructions for the installer 5. FINAL OPERATIONS After replacing the nozzles, reposition the flame-spreader crowns, the burner caps and the pan stands. Following adjustment to a gas other than the preset one, replace the gas adjustment label fixed to the appliance with the one corresponding to the new gas. The label is inserted inside the pack together with the nozzles. 5. 1 Regulation of the hob burner minimum for natural gas Light the burner and turn it to the minimum position . Extract the gas tap knob and turn the adjustment screw at the side of the tap rod until the correct minimum flame is achieved. Refit the knob and verify that the burner flame is stable (when turning the knob rapidly from the maximum to the minimum position the flame must not go out). Repeat the operation on all the gas taps. For models with valves, keep the knob at the minimum level for a few seconds to keep the flame lit and to activate the safety device. 5. 2 Regulation of the hob burner minimum for liquid gas In order to adjust the minimum setting with liquid gas, the screw at the side of the tap rod must be tightened clockwise all the way. The bypass diameters for each individual burner are shown in paragraphs "4. 2 Burner and nozzle characteristics table (60 cm model)" and "4. 3 Burner and nozzle characteristics table (90 cm model)". When the adjustment is completed, restore the sealing of the by-passes with paint or another material. 5. 3 Positioning and levelling the appliance (depending on the model) After making the electrical and gas connections, level the appliance on the floor by means of its four adjustable feet. For good cooking results, the appliance must be properly levelled. Depending on the model you have purchased, the foot height adjustment range may vary from 70 to 95 mm and from 110 to 160 mm. These heights refer to the distance between the highest point of the foot (fixed part) and the lowest point (movable part which rests on the floor). 5. 4 Adjustment of the oven burner minimum Light the burner and turn it to the minimum position . Extract the gas tap knob and turn the adjustment screw at the side of the tap rod until the correct minimum flame is achieved. Refit the knob and verify that the burner flame is stable (when turning the knob rapidly from the maximum to the minimum position the flame must not go out). Repeat the operation on all the gas taps. 14 Instructions for the installer 6. THE CONTROL PANEL All the cooker controls are grouped together on the front panel. The symbols used are described in the table below. TIMER KNOB 2-FUNCTION SELECTION KNOB GAS GRILL AND GAS OVEN THERMOSTAT KNOB FRONT LEFT-HAND BURNER KNOB REAR LEFT-HAND BURNER KNOB REAR CENTRAL BURNER KNOB FRONT CENTRAL BURNER KNOB REAR RIGHT-HAND BURNER KNOB FRONT RIGHT-HAND BURNER KNOB HOB BURNER CONTROL KNOB To light the flame, press the knob and turn it anticlockwise to the minimum flame symbol . To adjust the flame, turn the knob to the zone between the maximum ( ) settings. To turn off the burner, turn the knob to the position. ) and minimum ( TIMER KNOB In order to use the timer, the buzzer must be set by turning the knob in a clockwise direction. [. . . ] Replace the flame spreader crowns, making sure that they are correctly in place with their respective burner caps, making sure that the holes A in the flamespreaders are aligned with the igniters and thermocouples. 10. 2. 3 Igniters and thermocouples For correct operation, on those models that have them, the igniters and thermocouples must always be perfectly clean. Check them frequently and clean them with a damp cloth if necessary. Remove any dry residues with a wooden toothpick or a needle. 10. 3 Cleaning the oven For best oven upkeep, clean it regularly after having allowed it to cool. [. . . ]