User manual SMEG CBE66MF

[. . . ] Adjust the flame intensity to direct it onto the bottom of the pan only, making sure that it does not engulf the sides. Deep fat fryers must be continuously monitored during use: overheated oil can burst into flames. Do not flamb under the range hood; risk of fire This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. [. . . ] Clean and/or replace the Filters after the specified time period (Fire hazard). Clean the hood using a damp cloth and a neutral liquid detergent. The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product. EN 1 12 2 CHARACTERISTICS Dimensions min. 1 2 2. 1 2. 2 9 10 14. 1 15 Q. ty Product Components 1 Hood Body, complete with: Controls, Light, Blower, Filters 1 Telescopic Chimney comprising: 1 Upper Section 1 Lower Section 1 Reducer Flange 150-120 mm 1 Damper 2 Air Outlet Connection Extension 1 Air Outlet Connection 15 14. 1 253 433 90 9 10 12a 7. 2. 1 11 2. 1 2 2. 2 12c Ref. Q. ty Installation Components 7. 2. 1 2 Upper Chimney Section Fixing Brackets 11 6 Wall Plugs 12a 6 Screws 4, 2 x 44, 4 12c 6 Screws 2, 9 x 9, 5 Q. ty Documentation 1 Instruction Manual 1 11 12a EN 1 13 3 INSTALLATION Wall drilling and bracket fixing 12 11 12a 116 116 330 Wall marking: Draw a vertical line on the supporting wall up to the ceiling, or as high as practical, at the centre of the area in which the hood will be installed. Draw a horizontal line at 650 mm above the hob. Place bracket 7. 2. 1 on the wall as shown about 1-2 mm from the ceiling or upper limit aligning the centre (notch) with the vertical reference line. If this is not the case, adjust the position by either reversing the connection extension pieces 14. 1 and then reassemble as described previously. Ensure that the activated charcoal filters have been inserted. 15 14. 1 EN 1 15 5 ELECTRICAL CONNECTION Connect the hood to the mains through a two-pole switch having a contact gap of at least 3 mm. After 100 working hours all the LEDs (L1-L2-L3-L4) will light up and remain lit to indicate saturation of the metal grease filters. After 200 working hours all the LEDs (L1-L2-L3-L4) will light up and start to flash to indicate saturation of the activated charcoal filters. EN 1 17 7 MAINTENANCE Metal grease filters These can also be washed in the dishwasher, and need to be cleaned when all the command LEDs light up in a continuous manner or at least once every 2 months use, or more frequently if use is particularly intensive. Resetting the alarm signal Press any of the buttons except the Light button. Cleaning the Filters Remove the Filters one at a time, pushing them towards the back of the unit and at the same time pulling downward. Wash the Filters without bending them, and leave them to dry completely before replacing. Replace, taking care to ensure that the handle faces forwards EN 1 18 8 Activated Charcoal Filter (Recirculation Version) This cannot be washed or regenerated, and must be changed when all the command LEDs start to flash, or at least once every 4 months. Activating the alarm signal In Recirculation Version Hoods, the Filter Saturation Alarm must be activated on installation or at a later date. [. . . ] Activating the alarm signal In Recirculation Version Hoods, the Filter Saturation Alarm must be activated on installation or at a later date. Press and hold the Delay button (T4) on the keypad for 5 seconds and the following will be displayed: Leds (L1-L2-L3) flash twice Activated Charcoal Filter saturation alarm ACTIVATED. Leds (L1-L2-L3) flash once Activated Charcoal Filter saturation alarm DEACTIVATED. [. . . ]