User manual SMEG CS71-5

[. . . ] INSTRUCTIONS FOR SAFE AND PROPER USE _____________________ 32 INSTALLATION OF THE APPLIANCE ______________________________ 34 ADAPTATION TO DIFFERENT TYPES OF GAS______________________ 36 FINAL OPERATIONS ___________________________________________ 38 DESCRIPTION OF CONTROLS___________________________________ 39 USE OF THE COOKING HOB ____________________________________ 45 USE OF THE OVEN ____________________________________________ 46 AVAILABLE ACCESSORIES _____________________________________ 47 COOKING HINTS ______________________________________________ 48 CLEANING AND MAINTENANCE _________________________________ 52 EXTRAORDINARY MAINTENANCE _______________________________ 55 THESE INSTRUCTIONS ARE VALID ONLY FOR END USER COUNTRIES WHOSE IDENTIFICATION SYMBOLS APPEAR ON THE COVER OF THIS MANUAL. INSTRUCTIONS FOR THE INSTALLER: these are for the qualified technician who must carry out a suitable check of the gas system, install the appliance, set it functioning and carry out an inspection test. INSTRUCTIONS FOR THE USER: these contain user advice, description of the commands and the correct procedures for cleaning and maintenance of the appliance. 31 Introduction 1. INSTRUCTIONS FOR SAFE AND PROPER USE THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE AND THEREFORE MUST BE KEPT IN ITS ENTIRETY AND IN AN ACCESSIBLE PLACE FOR THE WHOLE WORKING LIFE OF THE COOKER. WE ADVISE READING THIS MANUAL AND ALL THE INSTRUCTIONS THEREIN BEFORE USING THE COOKER. [. . . ] Caution: for the oven to start cooking after the programming procedure just described, the thermostat and function selector must be properly set on the temperature and function required. 5. 2. 4 "DEMO" Function Models with analogue/digital programmer feature a "DEMO" function which deactivates the heating elements while leaving the other functions unchanged. To activate it, simply press the , and keys for 3/4 seconds. A confirmation beep will inform the user that the function is active. To deactivate it, simply repeat the same procedure. - 44 Instructions for the user 6. USE OF THE COOKING HOB 6. 1 Lighting of the cooking hob burners Before lighting the hob burners check that the flame-spreader crowns are located in their housing with their respective caps. Ensure that flamespreader holes A correspond to the spark plugs and the thermocouples. Grid B should be used for Chinese wok type pans. Each knob corresponds to the burner indicated. The appliance is equipped with an electronic lighting device. Just press and turn the knob anticlockwise to the maximum flame symbol until the burner lights. Keep the knob pressed for about 2 seconds to let the thermocouple heat up. If the burner turns off when the knob is released, it means that the thermocouple isn't hot enough. Repeat ignition and keep the knob pressed longer. Should the burners go out by accident a safety device intervenes to block gas supply even with the tap open. 6. 2 Practical advice for using the cooking hob burners For better use of the burners and lower gas consumption, use covered containers that are proportional in size to the burner to prevent the flame from licking the sides (see paragraph "6. 3 Diameter of containers"). When water reaches the boiling point, lower the flame so that it doesn't overflow. To avoid burns or damage to the hob, all recipients or griddle plates must be placed within the perimeter of the cooking hob. All containers have to have a flat and smooth bottom. When using fats or oils, be extremely careful that they don't overheat and catch fire. If the flame accidentally goes out, turn off the control knob and wait at least 1 minute before trying to re-light the burner. 6. 3 Diameter of containers BURNERS 1 2 3 4 Auxiliary Semi rapid Rapid Triple crown Ø min. (in cm) 12-14 16-24 18-26 18-26 45 Instructions for the user 7. USE OF THE OVEN 7. 1 Warnings and general advice Before using the oven for the first time, pre-heat it to maximum temperature (250°C) long enough to burn any manufacturing oily residues which could give the food a bad taste. [. . . ] Replace the flame-spreader crowns, checking that they are positioned in their housing with their respective caps, taking care that flame-spreader holes A correspond to the spark plugs and the thermocouples. 10. 2. 3 Ignition plugs and thermocouples To work well, the ignition plugs and thermocouples must always be very clean. Check them frequently and clean them with a wet rag if necessary. Any dry residue should be removed with a toothpick or a needle. 10. 3 Cleaning the inside of the oven For best oven upkeep clean regularly after having allowed to cool. [. . . ]