User manual SMEG CW511SD

[. . . ] THE MANUFACTURER DECLINES ALL RESPONSIBILITY FOR INJURY OR DAMAGE CAUSED BY FAILURE TO COMPLY WITH THE ABOVE REGULATIONS OR DERIVING FROM INCORRECT USE, TAMPERING WITH EVEN JUST ONE PART OF THE APPLIANCE AND THE USE OF NON-ORIGINAL SPARE PARTS. THE APPLIANCE MUST BE IN COMPLIANCE WITH ELECTRICAL SYSTEM SAFETY REGULATIONS. THIS APPLIANCE IS TAGGED UNDER EUROPEAN DIRECTIVE 2002/96/EC ON WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT (WEE). BY MAKING SURE THAT THIS PRODUCT IS DISPOSED OF CORRECTLY THE USER HELPS TO PREVENT POTENTIAL DETRIMENTAL EFFECTS ON HEALTH AND THE ENVIRONMENT. [. . . ] Connect to the detergent dispenser outside the dishwasher using the red hose mentioned above. IMPORTANT: Whenever the type of detergent or rinse aid is changed, it is ABSOLUTELY ESSENTIAL to flush out the peristaltic pumps by placing the external intake pipes in water for a few cycles. Always use only products specifically recommended for use in a dishwasher. The internal pipes of the detergent and rinse paid pumps should be replaced by the After-Sales Service every 12 months or 15, 000 wash cycles. Failure to comply with this recommendation leads to forfeiture of the warranty entitlement on the appliance's water system. 6 SETTINGS SETTINGS During start-up, the functions/parameters listed below must be set or adjusted: On first installation, a series of operations can be performed to allow the dishwasher to be customised to the user's needs. A short testing cycle can also be performed to verify operation of all the components. To perform these operations, access "programming mode" as explained below 7 6. 1 Dishwasher parameter modification procedure: (ONLY ACCESSIBLE AFTER FILLING IS COMPLETE or WITH THE DOOR OPEN) Indicator lights as follows: off; green; orange; flashing. on/off button for a few Access "programming mode" by pressing the seconds (UnLo 1:58 will appear on the display) with the appliance on (after the filling and heating phase); at the "beep", release the button and press it again quickly within 0. 5 seconds. Keep pressing the button again to scroll through all the modifiable parameters in the following order: Rinse aid delivery amount Detergent delivery amount Rinsing temperature Washing temperature Start-on/start-off. Set at "on" to start the cycle when the door is closed. Set at "off" for cycle start after confirmation with the start button Regeneration frequency, depending on water hardness (if softener is installed) tStP on/off "on" = minimum rinsing temperature as set, regardless of intake water temperature; the cycle duration may be a few seconds longer than the nominal length. "off" = the minimum rinsing temperature might be a few degrees lower than the setting if hot intake water is not used. Switch on the master switch (user): the word "OFF" appears on the display. The level of detergent and rinse aid in the containers. 8. 3 FIRST USE EACH DAY (tank and boiler empty) off; green; orange; flashing. Actions and what happens With the door closed: Press and hold it down the dishwasher fills the tank after the water in the boiler has heated up; light L2 shows orange and the boiler heating element symbol appears on the display. Wait for P1 to appear and LED L1 to change from orange to green; the tank heating element comes on until the set temperature is reached. The duration of this stage may vary depending on the mains water temperature and on the single-phase connection. Press the button to display the tank (left) and boiler (right) temperatures. Load the dishes Indicator lights as follows: Display shows Select the program required by pressing . Confirm the program start by pressing and holding it down for 1 second (light L2 changes from green to orange). 15 Cycle in progress, the time left until the end of the cycle is displayed. If the door is opened "CLOSE" flashes and the program stops; when it is closed again the program restarts from the beginning. At the end of the program "End" flashes Unload the dishes When the door is closed again, the last program is repeated. 8. 4 Program change With the door closed, to change to a fresh program instead of repeating the last one, press the button. The programs available are displayed (light L2 changes from orange to green). If a program has already started, hold interrupt it. down to change the program by pressing . Confirm the program start by pressing and holding it down for 1 second (light L2 changes back to orange). N. B. : During heating of the water in the boiler, the tank heating element may appear on the display. and boiler heating element symbols Filter presence sensor (on some models only) The filter is fitted with a sensor which checks that it is properly fitted; if it is not in the correct position, the word "FiLter" appears on the display. 16 9 CHOOSING THE PROGRAM PROGRAM P1 P2 P3 P4 Glasses Glasses, cups and plates with light dirt Very dirty dishes and cutlery Depending on the duration set. [. . . ] Do not use the products mentioned above even when cleaning the floor underneath or in the vicinity of the dishwasher, to ensure that fumes or drops cannot damage the steel surfaces. IMPORTANT: The dishwasher automatically performs program "P0" at the start of the day if water has been left in the tank and has dropped below the temperature of 40°C 11. 2 Periodic checks Remove the top and bottom spray arms by unscrewing the central screw and unscrew the caps from the ends of the rinsing arms as shown. Clean the holes and nozzles under a jet of clean running water; do not use tools which might cause damage. Reassemble the spray arms with care. Clean the outside of the appliance with a damp cloth and neutral soap, rinsing and drying thoroughly. 11. 3 Lengthy periods out of use If the dishwasher is to be out of use for a fairly long period of time, the detergent and rinse aid dispenser devices must be emptied to prevent crystallisation and damage to the pumps: Remove the intake hoses from the detergent and rinse aid containers and place them in a container of clean water, then perform a few wash cycles followed by a complete pump-out. [. . . ]