User manual SMEG CWG411MDSA

[. . . ] 11 Mains water hardness setting table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 7 8 MALFUNCTIONS SHOWN ON THE DISPLAY (FOR THE TECHNICIAN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 INSTRUCTIONS FOR THE USER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 8. 1 8. 2 8. 3 8. 4 8. 5 Control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Always use only products specifically recommended for use in a professional dishwasher. Failure to comply with this recommendation leads to forfeiture of the warranty entitlement on the appliance’s water system. The internal pipes of the detergent and rinse aid peristaltic pumps should be replaced by the AfterSales Service every 12 months or 15, 000 wash cycles. 5. 1 Using the water softener (on models with this feature only) The quantity of lime in the water (which indicates its hardness) causes whitish marks on dry dishes and dishes also tend to lose their shine over time. The dishwasher is equipped with an automatic water softener which removes the substances that cause hardness from the water with the aid of regenerating salt. The first time the dishwasher is used, a litre of water must be poured into the tank with the salt. Whenever the tank is filled, always take care to ensure that the cap is firmly closed. The mixture of water and detergent must not get into the salt tank, as this would impair operation of the regeneration system. In this case warranty cover will be forfeited. 7 SMEG 6 SET-UP (Authorised technical staff only) Set-up During first start-up, the functions/parameters listed below must be set or adjusted. Control Panel Key to Symbols On/off button Total pump-out (tank -boiler) button Regeneration button (only if softener is fitted) Regenerating salt symbol (only if softener is fitted) Short programme button Medium programme button Long programme button L1 L2 L3 L4 L5 L6 L7 Short programme Led Medium programme Led Long programme Led Resin regeneration Led (only if softener is fitted) Drainage Led Appliance on Led No salt Led (only if softener is fitted) Key to messages which scroll across display CLOSE FILL End PrF 400 UnLoad Close the door Machine preparing for cycle End of operation requested Appliance model (displayed when the appliance is switched on with the master switch). Pump-out 8 SMEG Using the buttons Button Short press Pressed for 2” Pressed for 5” Long press, release, press again Setup Menu (1) Start Pump-out Display of temperatures in On/OF Boiler (L3) and tank (L1) Scroll through Setup options (2) Set Pump-out Set Regeneration Start Regeneration (mod. with softener only) Set Short Programme Set Medium Programme Set Long Programme Set P0 Start Short Programme Start Medium Programme Start Long Programme Empty tank Peristaltic pumps in Manual mode to prime pipes Start P0 Start Test (1) Reset to DEFAULT parameters (3) Technician user only 1) Starting from appliance in “OF” status 2) From setup menu only. 3) Restores the default parameters, for new settings see point (6. 3) A series of operations can be carried out when the dishwasher is first installed to customise it to the user's requirements. 6. 1 Contents of display The two digits provide the following information: • Appliance off but powered up: all decimal points on both digits • Appliance on and ready for use : Tank temperature • Washing phase (programme running, washing pump in operation): Tank temperature • Rinsing phase (programme running, washing pump stopped): Boiler temperature • Programming phase: See parameter programming section • Error message: See error messages section 6. 2 Note on display of temperatures Temperatures shown on the display might not indicate the actual temperature in the tank and/or boiler during heating wait about 1’ after the heating elements switch off to see the real temperature. 6. 3 Parameter programming procedure To modify the parameters, proceed as follows starting with the appliance in “OF” status 1) switch the appliance using the On/OF button 2) hold down the button for about 4/5 seconds, until Led L6 goes out and then lights up again, then release the button and press it again. Pressed for 5” 8. 2 Before washing Use only detergents and rinse aids for industrial dishwashers. Do not use detergents intended for hand washing. We recommend the use of SMEG products, specially developed for this dishwasher. When topping up the tanks, take care not to swap the products; this might damage the dishwasher and cause malfunctions. Do not mix different detergents; this would damage the dispenser device. Failure to comply with this recommendation leads to forfeiture of the warranty entitlement on the appliance’s water system. Industrial dishwasher detergents may cause serious irritation. Comply carefully with the instructions provided by the detergent producer on the pack. Check 1. Turn on the mains water tap (user) 2. The level of detergent and rinse aid in the containers. 14 SMEG 3. That there is regenerating salt in the relative container (if fitted). 4. [. . . ] Spray arm washing holes blocked by dirt or limescale Filter fouled Too little or unsuitable detergent or rinse aid. No or not enough detergent or rinse aid being supplied: detergent or rinse aid not being taken from the relative container. Plates/glasses badly arranged Low washing temperature POSSIBLE REMEDY Check electrical mains connection. Wait for the end of the “FILL” phase Remove spray arms and clean them (routine checks). [. . . ]