User manual SMEG DOU330X

[. . . ] They will save you time and effort and help to ensure optimum oven performance. These installation instructions are intended for use by a qualified installer. In addition to these instructions, the oven shall be installed: In the United States, in accordance with the National Electric Code/State and Municipal codes and/or local codes. In Canada, in accordance wi th Canadian Electric Code C22. 1-latest edition/Pro vincial and Municipal codes and/ or local codes. [. . . ] DO NOT pinch the conduit between the oven back. WARNING Before installing or removing, turn power OFF at the service panel. Lock service panel to prevent power from being turned ON accidentally. Securely fasten oven to cabinet using the screws provided. Failure to do so could result in oven moving or tipping during use and causing damage to the oven or cabinets or personal injury. Know how to disconnect the power to the oven at the circuit breaker or fuse box in case of an emergency. 3. 4. 6. CAUTION Unit is heavy and requires equipment to move. A B C D E Cutout Width Cutout Depth Cutout Height DIMENSION SINGLE 30" 28 7/16" (72, 2 cm) 24" (61 cm) 27 3/8" (69, 5 cm) 34" (86, 5 cm) 1/2" (1, 3 cm) min DOUBLE 30" 28 7/16" (72, 2 cm) 24" (61 cm) 49 3/4" (126, 5 cm) N/A 1/2" (1, 3 cm) min Floor Bottom of Cutout Minimum Spacing 2 OVEN INSTALLATION MANUAL ENGLISH WALL OR UNDER COUNTER INSTALLATION, SINGLE OVEN Electrical supply junction box Electrical supply junction box Secure oven to cabinet using the screws provided. Screws should be inserted through the mounting holes in the positions indicated in the frame (open door to see frame and mounting holes). Do not over tighten screws. WALL INSTALLATION, DOUBLE OVEN Electrical supply junction box Secure oven to cabinet using the screws provided. Screws should be inserted through the mounting holes in the positions indicated in the frame (open door to see frame and mounting holes). Do not over tighten screws. 3 OVEN INSTALLATION MANUAL ENGLISH FLUSH INSTALLATION Ltr. F G H Cutout Width Cutout Height DIMENSION SINGLE 30" 30 1/16" (76, 4 cm) 28 1/32" (71 , 2 cm) 3/4" (1, 9 cm) DOUBLE 30" 30 1/16" (76, 4 cm) 51" (129, 5cm) 3/4" (1, 9 cm) Visible part of the mounting strips 4 OVEN INSTALLATION MANUAL ENGLISH ELECTRICAL SUPPLY Before installing the oven have a qualified electrician verify that your home is provided with adequate electrical service and that the addition of the oven will not overload the branch circuit on which it is to be installed. A separate three-wire or four-wire single phase, 240 Volt, 60 Hz, or a 208 Volt, 60Hz branch circuit is required. NOTE : FOR USE WITH 208 V, 60 HZ SUPPLY VOLTAGE, SEE CONNECTING TO 208 VOLT CIRCUIT. For hook-up of the oven you will need to have an approved junction box installed where it will be easily reached through the front of the cabinet where the oven will be located. Allow two to three feet of slack in the line so that the oven can be moved if servicing is ever necessary. DO NOT shorten the flexible conduit. CONNECTING TO 208 VOLT CIRCUIT This option is provided for areas where standard 240 Volt service is not available. This option must be accessed with the oven connected to power source, and using the following sequence: 1. Within five minutes from power up, hold [OPTIONS] and [TIME] keys for 3 seconds to enter the user option menu. 3. Hold then [TIME] and [LIGHT] keys until the display becomes dark. Hold [OPTIONS] and [LIGHT] further, until the time display shows "Volt" and temperature module shows "240" blinking, waiting for an input. Location of rating plate 4. 6. Using [INC] or [DEC] keys, the control toggles between 240V and 208V options. [. . . ] Check power at the junction box wires using a voltmeter x Move the knob back to "OFF" position to stop cooking. To check the other oven functions refer to the "Using the If you have installed the oven for use on 240 Volt supply, Oven Controls" section of the USE AND CARE MANUAL. you should find that the voltage reading between the black 7. If the oven is working properly, turn off the power supply to and red wires (Line to Line) should be 220 to 240 Volts. [. . . ]