User manual SMEG DRY2005

[. . . ] IT IS OBLIGATORY FOR THE ELECTRICAL SYSTEM TO BE GROUNDED ACCORDING TO THE METHODS REQUIRED BY SAFETY RULES. WHEN LINKING UP TO MAINS BY PLUG AND SOCKET, MAKE SURE THAT BOTH ARE COMPATIBLE AND CONNECT BY MEANS OF A POWER CABLE COMPLYING WITH APPLICABLE REGULATIONS. DO NOT OBSTRUCT VENTILATION OPENINGS AND HEAT DISPERSAL SLITS. IMMEDIATELY AFTER INSTALLATION CARRY OUT A BRIEF INSPECTION TEST OF THE STERILIZER, FOLLOWING THE INSTRUCTIONS BELOW. SHOULD THE APPLIANCE NOT FUNCTION, DISCONNECT IT FROM THE SUPPLY AND CALL THE NEAREST TECHNICAL ASSISTANCE CENTRE. NEVER ATTEMPT TO REPAIR THE APPLIANCE. 13 Introduction ALWAYS CHECK THAT THE CONTROL KNOBS ARE IN THE 0 (OFF) POSITION WHEN YOU FINISH USING THE STERILIZER. NEVER PUT INFLAMMABLE OBJECTS IN THE STERILIZER: THEY COULD BE ACCIDENTALLY LIGHTED AND CAUSE FIRES. THE I. D. [. . . ] CHILDREN SHOULD ALWAYS BE KEPT OUT OF ITS REACH AND NEVER BE ALLOWED TO PLAY WITH IT. THIS APPLIANCE IS MARKED ACCORDING TO THE EUROPEAN DIRECTIVE 2002/96/EC ON WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT (WEEE). THIS GUIDELINE IS THE FRAME OF A EUROPEAN-WIDE VALIDITY OF RETURN AND RECYCLING ON WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT. BEFORE THE APPLIANCE IS PUT INTO OPERATION, ALL THE LABELS AND PROTECTIVE FILMS APPLIED INSIDE OR OUTSIDE MUST BE REMOVED. The manufacturer declines all responsibility for damage to persons or things caused by non-observance of the above prescriptions or by interference with any part of the appliance or by the use of non-original spares. THE WARRANTY COVERS PRODUCTION DEFECTS AND IS SUBJECT TO THE CONDITIONS OF THE CERTIFICATE WHICH ACCOMPANIES THE APPLIANCE. 14 Instructions for the installer 2. INSTALLATION OF THE STERILIZER The sterilizer must be set up on a perfectly flat surface and left standing free. Make sure to allow enough room at the back for easy access to the terminal strip for connection of the power cable to mains. Installation must be carried out by a qualified technician in compliance with applicable regulations in force. 2. 1 Electrical connection Make sure that the power line voltage matches the specifications indicated on the rating plate located to the rear of the sterilizer. This rating plate must never be removed. The sterilizer is supplied complete with a H07RN-F three-core supply cable for operation from a 230V power supply. The standard cable is of the three-core 3 x 1. 5 mm2 H07RN-F type. If necessary the electrical supply cable should be replaced with an oil-resistant type (min. The (yellow/green) earth cable on the end of the cable to be connected to the sterilizer should be at least 20 mm longer. Make sure that plug and wall socket are of the same type and are in conformity with regulations in force. Also check that the power supply line is provided with adequate earthing. The orange light comes on and goes off various times during the cooking cycle indicating that the temperature in the sterilizer is being kept constant. TIMER KNOB SET TO MANUAL THERMOSTAT KNOB ON ANY POSITION Ex. 4. 4 Timed cooking The sterilizer heats up as signalled by the orange light going on. Upon the set temperature being reached, the light goes off. The orange light comes on and goes off various times during the cooking cycle indicating that the temperature in the sterilizer is being kept constant. Upon completion of the cooking cycle, the sterilizer automatically turns off, the green light comes on and the buzzer sounds for a few seconds. To completely turn off, set the thermostat knob to 0. TIMER KNOB ON ANY POSITION THERMOSTAT KNOB ON ANY POSITION Ex. Ex. 19 Instructions for the user 5. CLEANING AND MAINTENANCE Important: never spray water directly on to the sterilizer. Never use pressure nozzles. Before any intervention, disconnect the power supply of the sterilizer. 5. 1 Cleaning stainless steel parts To maintain stainless steel parts in perfect condition, clean regularly at the end of the work day. To clean and preserve the stainless steel surfaces, always use only specific products that do not contain abrasives or chlorine-based acids. [. . . ] Do not use metallic sponges or sharp scrapers: they will damage the surface. Use normal non-abrasive products for steel, and a wooden or plastic tool if necessary. Rinse thoroughly and dry with a soft cloth or deerskin. 20 Instructions for the user 5. 2 Cleaning the inside of the sterilizer To maintain the sterilizer in perfect condition, clean it regularly at the end of the work day. Remove the side guides by unscrewing the ring nut A and sliding them out of the rear hole B. · · Clean sterilizer grill and side guides with warm water and nonabrasive detergents. [. . . ]