User manual SMEG FP131X

[. . . ] INSTRUCTIONS FOR USE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . INSTRUCTIONS FOR DISPOSAL ­ OUR ENVIRONMENTAL CARE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GET TO KNOW YOUR OVEN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Turning PT1 to the right increases the time, allowing the cooking start time required to be set. A few seconds after the required duration is set, the and symbols will stop flashing and remain constantly on, and the oven will start to wait for the starting time set. At the end, the word STOP will appear on DSP1, cooking will stop and a buzzer will sound; press PT1 once to deactivate it. If you wish to continue cooking beyond the set time, press PT1 again. The oven will restart normal operation with the cooking settings selected previously. To switch the oven off completely, PT2 must be turned to 0. Modifying the data set Once automatic cooking has started, its duration can be changed. When the and symbols are steady and cooking is in progress, or the oven is in standby status waiting for cooking to start, press PT1 once. The symbol starts flashing and PT1 can be turned to change the set duration. Press PT1 again; the symbol goes out, the symbol will start to flash, and the cooking start time will be displayed on DSP1. The cooking start time can be increased or decreased by turning PT1. A few seconds after the last change, the and symbols will appear (in steady mode) on DSP1 and automatic cooking will restart with the new settings. 43 Instructions for the user 7. 6 Secondary menu This product also has a "secondary menu" that allows the user to: 1 2 Set the time shown on the display (DSP1). (P1: OF / ON) Activate or deactivate the child safety device ( ); this function, after 2 minutes of operation without any actions by the user, activates locking of all the functions and knobs; it is identified by the appearance of the ( ) symbol on DSP1. To temporarily deactivate locking and modify a cooking programme or selects a different function, keep PT1 pressed down until the ( ) symbol disappears from DSP1. At this point you can make the desired changes, and 2 minutes after the last setting, locking will be reactivated. To permanently deactivate locking you have to enter the secondary menu and deactivate it as described in this paragraph. (P2: OF / ON) Activate or deactivate the Show Room function; this function disables all the heating elements so that only the control panel works (To use the oven normally, set P2:OFF). 3 4 (P3: OF / ON) Activate or deactivate the function that allows a maximum consumption of 2300 W. When the child safety device is activated (P1:ON), if a knob is moved "bLOC" is displayed on DSP1 for 2 seconds. An action on PT2 also activates the "BLOC" alarm until the function originally selected is restored. 44 Instructions for the user 7. 6. 1 Change the settings in the secondary menu The secondary menu appears at first use, after a power failure or by holding PT1 down for 3 seconds with the oven in the OFF position (see point "7. 2 Operating modes"). Changing the parameters in the secondary menu is very simple. See the following diagram: MENU MODIFICATION PROCEDURE SYMBOLS Turn PT1 to the right to increase (+) the value or to set the ON status. Turn PT1 to the left to decrease (-) the value or to set the OFF status. Press PT1 to move to the next setting in the menu. After setting P3, press PT1 to resume normal operation of the oven. 45 Instructions for the user 7. 7 Cooling system The appliance is equipped with a cooling system which comes into operation as soon as a cooking function or a cleaning cycle (Pyrolysis) starts. [. . . ] These must be lowered during the insertion of the first middle glass pane acting as a seal between the frame and the pane of glass. · The second middle glass pane must be inserted first on the front part, on the second level (figure A), and then inserted on the back, again in the second level (figure B). · Replace the internal glass pane inserting it on the third level in the same way as described for the middle panes. Warning: replace the glass panes in the same order and in the same direction that they were removed. [. . . ]