User manual SMEG FTV3

[. . . ] 5 ACCESSORIES AVAILABLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 BEFORE INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 DESCRIPTION OF FRONT PANEL CONTROLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 USING THE OVEN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] will blink until the cavity temperature has 14 EN Instructions for the User 10. 1. 8 Hot Air function After selecting this function press PT1 to set the parameters and the duration light starts to blink. Turn PT1 to the right or left to change the preset cooking duration. Press PT2 to immediately start the cooking process or otherwise press PT1 to set a different time for the cooking process start. will blink until the cavity temperature has The temperature light reached the set value. 10. 1. 9 Pizza function After selecting this function press PT1 to set the parameters and the duration light starts to blink. Turn PT1 to the right or left to change the preset Pizza weight. 10. 1. 10 Special Functions Chose the Bread and Pizza/Gratin or Reheating & Sterilising pressing PT2. , Meat , Fish , Vegetables function in DSP3 by rotating and The display DSP1 shows the cooking time by default for the program displayed in DSP2 which also alternates with the predetermined temperature. The following screens show the first program corresponding to each one of the five Special Functions listed in 1 15 Instructions for the User EN Press PT1 to enter the Special Function and rotate it to select a program, the program starts to blink. The selection is linear from “X1” to “X5”, “X6” or “X14”, corresponding “X” to “A”, “B”, “C”, “P” or “R”. While the Special Function is being set the temperature is not displayed. Only the Special Function is displayed blinking. Press the PT1 knob to validate the program and enter the Cooking Time and rotate it to set a new value, the Cooking Time value and symbol start to blink. The oven incorporates a steam-reduction function that is activated when the Start/Stop key is pressed to gradually release the steam from the cavity, so that there is no sudden rush of steam when the appliance door is opened. This function takes around 3 minutes and during it the display shows the word “VAP”. WHEN OPENING THE DOOR DURING OR COMPLETION OF THE COOKING CYCLE WITHOUT STOPPING IT AS DESCRIBED ABOVE BE CAREFUL OF THE FLOW OF HOT AIR AND/OR STEAM COMING OUT OF THE COOKING CHAMBER. STEP BACK OR TO THE SIDE TO AVOID BURNS. At this point: Steam generation is stopped immediately although steam continues to be produced until the water cools down in the boiler. The cavity walls and the water tank are still very hot. The timer stops and the display shows the remaining amount of operating time. If you wish, at this time you can: Turn or stir the food to ensure it will be evenly cooked. Cancel a cooking cycle End of a cooking cycle. To restart the process, close the door and press PT2. 10. 2. 2 Modifying parameters The operating parameters (time, temperature, etc. ) can only be modified when the cooking process has been interrupted. [. . . ] The cooling fan keeps on working for some time. When the temperature has dropped sufficiently, the fan will switch itself off. If all the functions work properly it is probable that the lamp has blown. Perform water level calibration (see 8. 3. 2) Instructions for the User 14. 2 Replacing the light bulb EN WARNING: Ensure that the appliance is switched off before replacing the lamp to avoid the possibility of electric shock. [. . . ]