User manual SMEG GW4060C

[. . . ] BEFORE INSTALLATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 6. USING THE HOB. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 7. CLEANING AND MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 8. INSTALLING THE APPLIANCE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 9. [. . . ] We have provided a table below that summarises the kind of frying needed for the level selected. The green light coming on means that the appliance is powered (even when it is not in use). The indicator light comes on to indicate that the resistance is heating up. When this light goes out, the preset power level has been reached. When the light flashes regularly it means that the power of the hot plate is kept steady on the set level. The table below shows the power values which can be set, together with the corresponding type of food. Settings may vary depending on the amount of food and personal taste. Knob Position Suitable kind of cooking Chips Chicken Legs - Wings Appropriate Maximum amounts amounts (g) (g) 500 * * 250 500 750 * * 350 750 1 (160°C) 1-2 (170°C) Fried fish 2 (180°C) Fritters - Fish 2-3 (185°C) Croquettes - Cheese croquettes *= these levels depend mainly on the amount of food. Make sure they are completely immersed in the oil. 48 Instructions for the user 6. 6. 1 Some good frying tips The level of oil in the basin must always be between 3 litres (minimum amount indicated inside the basin) and 3. 5 litres (maximum amount indicated inside the basin). Under each cooking zone there is a coil called an inductor which is powered by an electronic system and which creates a variable magnetic field. When a pan is positioned within this magnetic field, the high frequency currents are concentrated directly onto the pan producing the heat required for cooking the food. After any zone is switched off, a flashing " "may appear on the display. This warns that the cooking zone concerned is still very hot. Cooking can be restarted while the " point "3". " is flashing: in this case, proceed as described in 6. 7. 7 Cooking hob lock-out When not in use, the hob can be "locked" from being accidently turned on by children. With the hotplates switched off, turn the control knobs to the left at the same time until the power display shows the letter "L", then release the knobs. To unlock it repeat the same operation: The burners' displays will show a 0 that will indicate that the burners' lock has been deactivated. 6. 7. 8 Circuit board thermal protection The appliance is provided with a device that constantly measures the temperature of the electronic circuit board. If the temperature surpasses certain values, the device will activate certain functions to lower the temperature and allow the glass ceramic hob to continue to work correctly. Below is a table with the operations that are activated automatically and the relative start temperature: 54 Instructions for the user Operation Fan turns on at low speed Fan turns on at high speed Fan returns to low speed Fan turns off Operating power reduced from Power to 9 Reduction of power of a point for every cooking zone Turning off all the cooking zones Switching the cooking zones on again at reduced power Normal operation of all the cooking zones Activating temperature 50° C 60° C 55° C 45° C 76° C 85° C 90° C 85° C 80° C Every intervention of this type will be identified on the cooking hob with a flashing light on the power display. 6. 7. 9 Glass ceramic hob thermal protection Every cooking zone has a device that constantly measures the temperature. If the temperature surpasses certain values, the device will activate certain functions to lower the temperature and allow the glass ceramic hob to continue to work correctly. [. . . ] For supplying it with other types of gas, see chapter "10. ADAPTATION TO DIFFERENT TYPES OF GAS". The gas inlet connection is threaded ½" external gas (ISO 228-1). Connection with rigid copper hose: The connection to the gas supply network must be carried out in such a way that it does not cause stress of any kind to the appliance. [. . . ]