User manual SMEG KI90CT-1

[. . . ] 20 NDICE PT CONSELHOS E SUGESTES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 CARACTERSTICAS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 INSTALAO. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product. EN 3 3 CHARACTERISTICS Dimensions min. 861 -max. 1146 696 120 20 898 350 150 Min. 650mm 650mm 698 290 EN 306 90 130 4 4 Components Ref. 1 2 2. 1 2. 2 7. 1 7. 1a 7. 1b 8a 8b 9 10 14 14. 1 15 24 25 Ref. 11 12c 12e 12f 12g 12h 12q 21 22 23 Q. ty Product Components 1 Hood Body, complete with: Controls, Light, Blower, Filters 1 Telescopic Chimney comprising: 1 Upper Section 1 Lower Section 1 Telescopic frame complete with extractor, consisting of: 1 Upper frame 1 Lower frame 1 Right Air Outlet Grill 1 Left Air Outlet Grill 1 Reducer Flange 150-120 mm 1 Damper (Optional) 1 Hood Body Air Outlet Extension Piece consisting of two Half Shells(Optional) 1 Air Outlet Connection Extension 1 Air Outlet Connection 1 Junction box Pipe clamps (not included) Q. ty Installation Components 4 Wall Plugs 10 6 Screws 2, 9 x 6, 5 2 Screws 2, 9 x 9, 5 2 Screws M4 x 80 4 Screws M6 x 80 4 Screws 5, 2 x 70 4 Screws 3, 5 x 9, 5 1 Drilling template 8 6. 4 mm int. dia washers 4 M6 nuts Q. ty Documentation 1 Instruction Manual 21 23 22 7. 1a 12g 7. 1 11 12h 15 14. 1 7. 1b 9 12c 2. 1 2 2. 2 8b 8a 12e 24 25 12c 12c 1 12f 22 12q EN 5 5 INSTALLATION Drilling the Ceiling/shelf and fixing the frame DRILLING THE CEILING/SHELF Use a plumb line to mark the centre of the hob on the ceiling/support shelf. Place the drilling template 21 provided on the ceiling/support shelf, making sure that the template is in the correct position by lining up the axes of the template with those of the hob. Mark the centres of the holes in the template. Drill the holes at the points marked: For concrete ceilings, drill for plugs appropriate to the screw size. For hollow brick ceilings with wall thickness of 20 mm: drill 10 mm(immediately insert the Dowels 11 supplied). For wooden beam ceilings, drill according to the wood screws used. For the power supply cable feed, drill 10 mm. For the air outlet (Ducted Version), drill according to the diameter of the external air exhaust duct connection. Insert two screws of the following type, crossing them and leaving 4-5 mm from the ceiling: For concrete ceilings, use the appropriate plugs for the screw size (not provided). for Cavity ceiling with inner space, with wall thickness of approx. For wooden beam ceilings, use 4 wood screws (not provided). For wooden shelf, use 4 screws 12g with washers 22 and nuts 23, provided. EN 6 6 Fixing the frame Loosen the two screws fastening the lower chimney and remove this from the lower frame. Loosen the two screws fastening the upper chimney and remove this from the upper frame. If you wish to adjust the height of the frame, proceed as follows: Unfasten the metric screws joining the two columns, located at the sides of the frame. [. . . ] Before fixing the hood canopy to the frame: Screw the 2 screws 12f half way into the holes provided in the sides of the bottom of the frame. Remove the grease filters from the hood canopy. Lift the hood canopy and engage the screws 12f in the slots (A) as far as they will go. [. . . ]