User manual SMEG LBW105DS

[. . . ] WASHING MACHINE USER MANUAL LBW105DS BEFORE USING THE WASHING MACHINE, YOU SHOULD CERTAINLY READ THE INFORMATION IN USER’S MANUAL. CONTENTS CHAPTER-1: TECHNICAL SPECIFICATIONS CHAPTER-2: BEFORE USING WASHING MACHINE Safety warnings Recommendations CHAPTER-3: SETTING UP . . . . . Removing transport safety screws Adjusting adjustable stays Electrical connection Water inlet connection Water discharge connection CHAPTER-4: PRELIMINARY PREPARATION FOR LAUNDERING CHAPTER-5: CONTROL PANEL Detergent drawer Programme knob Spin speed selector knob Electronic display CHAPTER-6: OPERATING YOUR MACHINE Selecting programme Auxiliary functions Starting the programme Child lock Cancelling programme Finishing programme CHAPTER-7: WARNING SYMBOLS Warning of water cut-off/low mains water pressure Warning of clogged pump fitler CHAPTER-8: MAINTENANCE AND CLEANING OF YOUR MACHINE CHAPTER-9: PRACTICAL INFORMATION CHAPTER-10: TROUBLESHOOTING CHAPTER-11: AUTOMATIC FAULT WARNINGS AND WHAT TO BE DONE CHAPTER-12: DESCRIBING AND SAVING ENERGY 3 5 5 6 7 7 9 10 10 11 12 16 17 18 19 20 21 21 21 27 28 29 30 31 31 32 33 38 40 45 47 2 CHAPTER -1: TECHNICAL SPECIFICATIONS 2 3 4 1 1. Detergent drawer 2. Upper tray 3. Programme knob 4. Electronic display 5. Door 6. Cover of pump filter 5 6 8 9 10 7 7 7. Transport safety screw 8. Power cable 9. Discharging hose 10. Water inlet valve 7 7 3 CHAPTER -1: TECHNICAL SPECIFICATIONS Operating voltage / frequency (V/Hz) Total current (A) Water pressure (Mpa) Total power (W) Maximum dry laundry capacity (kg) Wringing revolution (rev / min) Programme number Dimensions (Height x Width x Depth) (mm) (220-240) V ~/50Hz 10 Maximum: 1 Mpa Minimum: 0. 1 MPa 1850 5 1000 15 845 x 597 x 416 4 CHAPTER -2: BEFORE USING YOUR WASHING MACHINE SAFETY WARNINGS SAFETY WARNINGS Do not use multiple receptacles or extension cord. In case of a breakdown of power cable, contact the nearest authorized service for replacing it. Do not plug-in or out the plug from the receptacle with wet hands to prevent electric shock. [. . . ] The child lock will become active after the first and second function buttons on the control panel are pressed at the same time and for longer than 5 seconds. When it becomes active the electronic display will blink “CL” and child lock light will light up. If pressed any button while child lock is active, child lock light will blink on the electronic display. When any of the programmes is running and child lock is active, if another programme is selected after programme knob is switched to 0 position, the programme already running will resume. To deactivate it, it will be sufficient to press on the same buttons for more than 5 seconds. When child lock is deactivated, child lock light on the electronic display will go off. 28 CHAPTER 6: OPERATING YOUR MACHINE CANCELLING PROGRAMME Cancelling programme If you want to cancel any programme running: - Switch the programme knob to 0. - Your machine will stop the washing operation and the programme will be cancelled. - To get rid of the water accumulated in the machine switch the programme knob to any programme. - Your machine will perform the necessary discharge operation and cancel the programme. - You can run your machine by selecting a new programme. 29 CHAPTER 6: OPERATING YOUR MACHINE FINISHING PROGRAMME Finishing programme - Your machine will stop by itself as soon as the programme you have selected finishes. -Expression of “END” will flash on the electronic display. - Leave the door of your machine open to allow the inner part of your machine to dry after removing your laundries. - Turn the water faucet off. 30 CHAPTER -7: WARNING SYMBOLS WARNING OF WATER CUT-OFF / LOW MAINS WATER PRESSURE If symbol flashes on the control panel: - Water faucet may be closed. If so, switch the programme knob to position 0. You can select a programme and run your machine after the mains water is supplied. (*) - Valve inlet filter may be clogged. (*) (*) See the chapter regarding maintenance and cleaning of your machine. 31 CHAPTER -7: WARNING SYMBOLS WARNING OF CLOGGED PUMP FILTER If symbol flashes on the control panel: - Pump filter may be clogged. (*) - Discharging hose may be clogged or twisted. Check the discharging hose. (*) See the chapter regarding maintenance and cleaning of your machine. 32 CHAPTER -8: MAINTENANCE AND CLEANING OF YOUR MACHINE Unplug your machine. Turn the water faucet off. WATER INLET FILTERS Filters to avoid dirt and foreign substances in the water from penetrating into the machine are available both on the side of faucet and on the ends of water valves along the water inlet hose of your machine. If your machine cannot intake sufficient amount of water despite water faucet being open, these filters should be cleaned. Remove the filters on water inlet valves using pliers and then clean it with a brush in water. Disassemble the filters on the side of faucet side of water inlet hoses manually and clean it. Having the filters cleaned, you can fit them in the same way reversely. [. . . ] (**) See the chapter regarding installation of your machine. 43 CHAPTER -10: TROUBLESHOOTING FAULT POSSIBLE CAUSE REMOVING METHODS Unbalanced load control system will try to spread your laundries homogeneously. Wringing operation will start after spreading your laundries. Put your laundries in the machine homogeneously in the next washing operation. Wringing operation is not performed or runs late. No fault. Unbalanced load control system has been activated. 44 CHAPTER -11: AUTOMATIC FAULT WARNINGS AND WHAT TO BE DONE Your machine is equipped with the systems which are capable of both taking necessary precautions and warning you in case of any breakdown by means of continuous self-checking during washing operations. [. . . ]