User manual SMEG PC68

[. . . ] 11 Mains water hardness setting table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 7 8 MALFUNCTIONS SHOWN ON THE DISPLAY (FOR THE TECHNICIAN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 INSTRUCTIONS FOR THE USER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 8. 1 8. 2 8. 3 8. 4 8. 5 Control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The terminal for the connection is in the bottom righthand corner of the appliance. Always use only products specifically recommended for use in a professional dishwasher. Failure to comply with this recommendation leads to forfeiture of the warranty entitlement on the appliance’s water system. The internal pipes of the detergent and rinse aid peristaltic pumps should be replaced by the AfterSales Service every 12 months or 15, 000 wash cycles. 5. 1 Using the water softener (on models with this feature only) The quantity of lime in the water (which indicates its hardness) causes whitish marks on dry dishes and dishes also tend to lose their shine over time. The dishwasher is equipped with an automatic water softener which removes the substances that cause hardness from the water with the aid of regenerating salt. The first time the dishwasher is used, a litre of water must be poured into the tank with the salt. Whenever the tank is filled, always take care to ensure that the cap is firmly closed. The mixture of water and detergent must not get into the salt tank, as this would impair operation of the regeneration system. In this case warranty cover will be forfeited. 7 SMEG 6 CWG411MDA SET-UP (Authorised technical staff only) Set-up During first start-up, the functions/parameters listed below must be set or adjusted. Control Panel Key to Symbols On/off button Total pump-out (tank -boiler) button Regeneration button (only if softener is fitted) Regenerating salt symbol (only if softener is fitted) Short programme button Medium programme button Long programme button L1 L2 L3 L4 L5 L6 L7 Short programme Led Medium programme Led Long programme Led Resin regeneration Led (only if softener is fitted) Drainage Led Appliance on Led No salt Led (only if softener is fitted) Key to messages which scroll across display CLOSE FILL End PrF 400 UnLoad Close the door Machine preparing for cycle End of operation requested Appliance model (displayed when the appliance is switched on with the master switch). Pump-out 8 SMEG Using the buttons Button Short press CWG411MDA Pressed for 2” Pressed for 5” Long press, release, press again Setup Menu (1) Display of temperatures in On/OF Boiler (L3) and tank (L1) Scroll through Setup options (2) Set Pump-out Start Pump-out Set Regeneration Start Regeneration (mod. with softener only) Set Short Programme Set Medium Programme Set Long Programme Set P0 Start Short Programme Start Medium Programme Start Long Programme Empty tank Peristaltic pumps in Manual mode to prime pipes Start P0 Start Test (1) Reset to DEFAULT parameters (3) Technician user only 1) Starting from appliance in “OF” status 2) From setup menu only. Pump-out 13 SMEG Using the buttons Button Short press Display of temperatures in Boiler (L3) and tank (L1) CWG411MDA Pressed for 2” On/OF Start Pump-out Start Regeneration Start Short Programme Start Medium Programme Start Long Programme Pressed for 5” Set P0 Start programme P0: emptying of tank to clean filters. Switch off and back on to allow reuse. 8. 2 Before washing Use only detergents and rinse aids for industrial dishwashers. Do not use detergents intended for hand washing. We recommend the use of SMEG products, specially developed for this dishwasher. When topping up the tanks, take care not to swap the products; this might damage the dishwasher and cause malfunctions. Do not mix different detergents; this would damage the dispenser device. Failure to comply with this recommendation leads to forfeiture of the warranty entitlement on the appliance’s water system. Industrial dishwasher detergents may cause serious irritation. Comply carefully with the instructions provided by the detergent producer on the pack. Check 1. Turn on the mains water tap (user) 2. The level of detergent and rinse aid in the containers. 14 SMEG CWG411MDA 3. [. . . ] The detergent and rinse aid intake hoses must be put back into the containers when the dishwasher is returned to service, taking care not to swap them over (red hose = detergent, blue hose = rinse aid). 18 SMEG CWG411MDA 10 TROUBLESHOOTING How to deal with any problems without calling the after-sales service PROBLEM Led 6 does not light up Washing program does not start Poor washing results POSSIBLE CAUSE Mains power failure The dishwasher has not yet finished filling. Spray arm washing holes blocked by dirt or limescale Filter fouled Too little or unsuitable detergent or rinse aid. No or not enough detergent or rinse aid being supplied: detergent or rinse aid not being taken from the relative container. Plates/glasses badly arranged Low washing temperature POSSIBLE REMEDY Check electrical mains connection. [. . . ]