User manual SMEG PS15

[. . . ] ALSO KEEP THE SET OF NOZZLES PROVIDED IN A SAFE PLACE. INSTALLATION MUST BE CARRIED OUT BY QUALIFIED STAFF IN COMPLIANCE WITH THE RELEVANT REGULATIONS. THIS APPLIANCE IS INTENDED FOR HOUSEHOLD USE AND COMPLIES WITH THE EEC DIRECTIVES CURRENTLY IN FORCE. THE APPLIANCE IS BUILT TO PROVIDE THE FOLLOWING FUNCTION: COOKING AND HEATING FOODS; ALL OTHER USES ARE TO BE CONSIDERED IMPROPER. [. . . ] Follow the dimensions shown, bearing in mind that the long front edge must be flush with the hole. 2. 3 Fixing using brackets Fix the hob to the structure using the brackets A provided. Carefully trim off the excess edge of the gasket B. The dimensions in the drawing below refer to the hole on the inside edge of the gasket. See right for the precise holes to be used when securing the hob to the top correctly using the brackets. 22 Instructions for the Installer 3. Electrical connection Check that the power supply line voltage and size are as specified on the nameplate underneath the appliance's casing. This nameplate must never be removed. The plug on the end of the power supply lead and the wall socket must be of the same type and comply with the relevant regulations. Check that the power supply line is properly earthed. Pass the power supply cable through the rear of the cabinet, taking care that it does not touch the bottom case of the hob, or the oven (if any) built in underneath it. The appliance's power supply line must be fitted with an omnipolar breaking device with contact gap of at least 3 mm, located in an easily accessible position close to the appliance itself. The use of reductions, adapters or junctions is not recommended. If the power supply cable has to be replaced, the gauge of the wires in the new cable must be at least 0. 75 mm2 (3 x 0. 75 cable), bearing in mind that the earth wire (yellow-green) must be at least 20 mm longer at the end for connection to the appliance. Use only a type H05V2V2-F or similar cable resistant to a temperature of up to 90°C. The cable must be replaced by a qualified electrician, who must make the mains connection as shown below. L = brown N = blue = yellow-green The power supply lead must be replaced by an authorised service centre to prevent all risks. The manufacturer declines all responsibility for injury or damage caused by failure to comply with the above regulations or deriving from tampering with even just one part of the appliance. 23 Instructions for the Installer 4. Gas connection If the appliance is installed above an oven, the gas hose must be passed around the back of the oven to prevent overheating. 1 · Remove the hob skin fixing screws. 2 · After removing all the components described above, lift off the hob skin. Release all snap connections simultaneously (the hob is connected to the casing underneath in 5 points). 3 During reassembly, after putting the hob skin in position, press down on the points shown above to snap all the connections back into place. 25 Instructions for the Installer 5. 2 Adjusting for bottled gas Undo the screw C and push the air regulator D fully down. Remove the nozzle E with a 7 mm spanner and fit the suitable one, following the instructions in the tables referring to the type of gas to be used. The nozzle must not be tightened with a torque of more than 3 Nm. Regulate the air flow by sliding the regulator D along until the distance "X" stated in point "0 Adjusting the primary air flow" is obtained. Fix the regulator D by tightening the screw C. Burner Rated heat capacity (kW) Nozzle diameter 1/100 mm Auxiliary Semi rapid Rapid Ultra Rapid 1. 05 1. 7 3. 0 4. 2 48 62 82 98 Bottled gas ­ G30/G31 30/37 mbar By-pass mm 1/100 30 32 50 63 Reduced heat capacity (W) 400 450 1050 1600 Flow rate g/h G30 76 124 218 305 Flow rate g/h G31 75 121 214 300 26 Instructions for the Installer 5. 3 Adjusting for natural gas The appliance is tested with G20 (2H) natural gas at the pressure of 20 mbar. To return the appliance to the condition required to use this type of gas, proceed as described in point "5. 2 Adjusting for bottled gas" but select the nozzles and adjust the primary air flow for natural gas, as indicated in the table below and in point "5. 4 Adjusting the primary air flow". Burner Rated heat Capacity (kW) Natural gas - G20 20 mbar Nozzle diameter 1/100 mm 73 92 123 150 Reduced heat capacity (W) 400 450 1050 1400 Auxiliary Semi rapid Rapid Ultra Rapid 1. 05 1. 7 3. 0 4. 2 5. 4 Adjusting the primary air flow Refers to the gap "X" in mm. BURNER Auxiliary Semi rapid Rapid Ultra Rapid G20 20 mbar 0. 5 0. 5 2 4 G30/G31 30/37 mbar 3 2 3 10 To identify the burners on your hob, refer to the drawings in point "5. 8 Hob burner layout". 27 Instructions for the Installer 5. 5 Reassembling the hob skin Reverse the procedure described in point "5. 1 Removing the hob skin". Fit the pan stands as described in point "7. 1 Fitting the Pan Stands". 5. 6 Adjusting the minimum for natural gas Reassemble the components on the burner and fit the knobs onto the tap rods. Light the burner and turn it to the minimum setting. Be very careful to match the different central diameters of the pan stands to the flamespreader crowns. At the ends of the legs of the pan stands there are silicone gaiters with a hole that must be centred onto the matching fixing pins on the hob. To position the pan stand, you first need to centre the fixing pins (1) and (2) and then lower it until it is resting on the hob. [. . . ] Instructions for use: pour the product onto a damp cloth and wipe over the surface, then rinse thoroughly and dry with a soft cloth or chamois leather. 8. 1. 2 Food stains or spills Never use metal scouring pads or sharp scrapers which will damage the surface. Use ordinary non-abrasive products for glass, with the aid of non-scratching sponges and wooden or plastic utensils if necessary. Rinse thoroughly and dry with a soft cloth or chamois leather. 8. 2 Cleaning the components Never clean the knobs with aggressive products containing alcohol or steel or glass cleaners, since they might cause permanent damage. The components described below must never be washed in a dishwasher. [. . . ]