User manual SMEG PVA750A

[. . . ] Precautions for safety and use_________________________ 4 2. Instructions for disposal ­ our enviromental care___________ 5 3. Safety instructions __________________________________ 6 4. Fitting the appliance in the top _________________________ 7 4. 1 4. 2 4. 3 4. 4 Fixing to the supporting structure ________________________________________7 Fitting the adhesive foam rubber strip_____________________________________8 Fitting the fixing clips _________________________________________________8 Fitting the hob into the hole in the work-top ________________________________8 5. [. . . ] Then lower the front of the hob until the appliance is completely in place. 8 Instructions for the Installer 5. Electrical connection Check that the power supply line voltage and size are as specified on the nameplate underneath the appliance's casing. This nameplate must never be removed. The plug on the end of the power supply lead and the wall socket must be of the same type and comply with the relevant regulations. Check that the power supply line is properly earthed. Pass the power supply cable through the rear of the cabinet, taking care that it does not touch the bottom case of the hob, or the oven (if any) built in underneath it. If the appliance is connected to the power grid using a fixed connection, fit the power line with an omnipolar circuit-breaker, in accordance with the installation instructions, located in a readily accessible position near the appliance. The use of reductions, adapters or junctions is not recommended. If the power supply cable has to be replaced, the gauge of the wires in the new cable must be at least 0. 75 mm2 (3 x 0. 75 cable), bearing in mind that the earth wire (yellow-green) must be at least 20 mm longer at the end for connection to the appliance. Use only a type H05V2V2-F or similar cable resistant to a temperature of up to 90°C. The cable must be replaced by a qualified electrician, who must make the mains connection as shown below. L = brown N = blue = yellow-green The power supply lead must be replaced by an authorised service centre to prevent all risks. The manufacturer declines all responsibility for injury or damage caused by failure to comply with the above regulations or deriving from tampering with even just one part of the appliance. 9 Instructions for the Installer 5. 1 Clearances above and around domestic appliances Extract from AS5601 REQUIREMENTS 1. Overhead clearances ­ (Measurement A) Range hoods and exhaust fans shall be installed in accordance with the manufacturer's instructions. However, in no case shall the clearance between the highest part of the hob of the cooking appliance and a range hood be less than 600 mm or, for an overhead exhaust fan, 750 mm. Any other downward facing combustible surface less than 600 mm above the highest part of the hob shall be protected for the full width and depth of the cooking surface area in accordance with Clause 5. 12. 1. 2. However, in no case shall this clearance to any surface be less than 450 mm. flexible hose according to AS/NZ1869 & be at least Class "B", 10 mm diameter. The appliance must be installed with provision to allow the gas to be turned off and disconnected for servicing and removal of the appliance as required from the gas supply. Before the appliance is operated make certain all relevant parts are placed in the correct position. When the installation is completed the installation connections of appliance will require to be leak tested, the burner operating pressure and flame checked and adjusted. Warranty service calls do not cover these adjustments!To check the operating pressure of the appliance it is recommended at least 2 large size burners are used. Ensure appliance is secured to wall when installation is completed. The regulator supplied must be fitted to the ½ BSP thread at the rear of the appliance. An approved manual shut-off valve must be installed. regulator must be checked and adjusted to 1. 0kPa after installation. Can be connected to the inlet fitting directly. [. . . ] The burner may go out when the knob is released. In this case, repeat the operation, keeping the knob pressed down for longer. When the burner has lit, its control knob will light up to confirm that it is in operation. The knob will go out a few seconds after it is turned to the O position, or if the burner goes out accidentally. [. . . ]