User manual SMEG PW4060

[. . . ] PW4060 PUNCH WASHER USER MANUAL READ THE USER MANUAL WITH CARE This manual is an integral part of the appliance. Take good care of it and keep it to hand throughout the appliance’s life cycle. This manual and all the information it contains must be read carefully before using the appliance. Failure to read, any misunderstanding or incorrect interpretation of the instructions provided in this manual may lead to misuse of the device, put the operator at risk and impair the device’s performance. [. . . ] 32 – SET appliance parameters; parameter –b is used to enable and disable overwriting of the internal data memory. The following is an example of data stored in the internal memory, with a key to their interpretation. The data can be accessed using the TRACELOG software. User Manual PW4060 Series Page 42 - 78 The double line marks the start and end of a program ================================================================================ 2012/10/17 10:39:46START PROGRAM: 7Oper: 255 Consecutive number of cycle Cycle N. : 288 2012/10/17 10:40:17START PHASE N. : 1 First phase, called “1” 2012/10/17 10:41:12Inflow Detergents P1:0. 40% 2012/10/17 10:42:26TL1: 22. 7TCL: 22. 5 2012/10/17 10:42:26Start heating Target temp. 93 P1 detergent dispensing 2012/10/17 10:56:12TL1: 94. 1TCL: 93. 6 2012/10/17 10:57:36TL1: 93. 9TCL: 93. 4 2012/10/17 10:57:52TL1: 94. 1TCL: 93. 6 2012/10/17 10:59:43TL1: 93. 9TCL: 93. 4 Phase Target temperature 2012/10/17 10:59:58TL1: 94. 1TCL: 93. 6 2012/10/17 11:01:53TL1: 93. 9TCL: 93. 4 2012/10/17 11:02:08TL1: 94. 1TCL: 93. 6 2012/10/17 11:04:12TL1: 93. 9TCL: 93. 4 2012/10/17 11:04:26TL1: 94. 1TCL: 93. 5 A0 value reached 2012/10/17 11:05:53Ao>=15983 2012/10/17 11:05:53Start heating Target temp. 0 2012/10/17 11:05:53TL1: 94. 1TCL: 93. 6 2012/10/17 11:07:49START PHASE N. : 2 Second phase, called “2” 2012/10/17 11:08:41Inflow Detergents P2:0. 20% 2012/10/17 11:09:34TL1: 43. 3TCL: 42. 3 2012/10/17 11:09:34Start heating Target temp. 0 The two tank temperature 2012/10/17 11:11:34TL1: 59. 7TCL: 59. 2 probes are called: 2012/10/17 11:11:34Start heating Target temp. 0 TL1 – working probe TCL – control probe 2012/10/17 11:11:34TL1: 59. 7TCL: 59. 2 2012/10/17 11:12:33START PHASE N. : 3 2012/10/17 11:13:19Inflow Detergents 2012/10/17 11:13:41TL1: 36. 9TCL: 36. 5 2012/10/17 11:13:41Start heating Target temp. 0 2012/10/17 11:15:41TL1: 49. 9TCL: 49. 5 2012/10/17 11:15:41Start heating Target temp. 0 2012/10/17 11:15:41TL1: 49. 9TCL: 49. 5 2012/10/17 11:16:41START PHASE N. : 4 2012/10/17 11:17:26Inflow Detergents 2012/10/17 11:17:49TL1: 33. 3TCL: 32. 9 2012/10/17 11:17:49Start heating Target temp. 75 2012/10/17 11:25:47TL1: 76. 2TCL: 75. 7 Drying phase, with Target 2012/10/17 11:26:30Start heating Target temp. 0 temperature in Dryer duct 2012/10/17 11:26:30TL1: 76. 9TCL: 76. 5 2012/10/17 11:27:29Start drying: TA_TARGET: 120TA1: 73 2012/10/17 12:04:47End drying: TA1: 89 2012/10/17 12:09:07END PROGRAM: 7 ================================================================================ fig. 33 – Example of cycle data stored in the appliance’s memory. User Manual PW4060 Series Page 43 - 78 5. 4 “CLOC” – DATE AND TIME PARAMETERS The “Cloc” parameter (an abbreviation of “CLOCK”), is used to modify the current date and time. The parameter can be set with a user password as well. Proceed as follows: a. To select the Cloc parameter, hold down button 3 - Start/Stop with “Cloc” on the display. Button 5 - Functions, short press: to move from one parameter to the next (or buttons 2 and 6 - Drying Decrease/Increase). Use the Selection buttons 4 and 8 to modify the value of the parameter. Hold down button 3 - Start/Stop to confirm the modification. Hold down button 7 - Open door to quit the parameter being modified and the Cloc function. The parameter flashes while it is being set. CLOC PARAMETER C1 C2 C3 C4 C5 C6 DESCRIPTION Year, last two digits (00-99), e. g. for “2012” enter “12” Month (1-12) Day (1-31) Hour (1-24) Minutes (0-59) Seconds (0-59) fig. Hold down the Start/Stop button to access the parameters, in this case identified as C1, C2, etc. Parameter C1 sets the current year, C2 the month, etc. [. . . ] The water drain connections may be on the right or left of the appliance, always considering the maximum distance “I_max”. MODELS N. DRAIN HOSES 2 Distance “I_max” Maximum distance of drain from side of appliance [cm] 50 PW4060 DRAIN TYPE AND HEIGHT “H” ABOVE APPLIANCE INSTALLATION SURFACE [cm] Type H_min H_max d 65 80 cd 65 80 Note about product “families” Suffix "C" indicates "equipped with steam condenser. " Any additional suffixes ". . " may vary depending on the appliance version. fig. Drain connections – 65 cm < H < 80 cm. Height difference “X”: only use original drain hoses and the “hose guide” elbows provided. [. . . ]