User manual SMEG S809A

[. . . ] NEVER ATTEMPT TO REPAIR THE APPLIANCE YOURSELF. AFTER EACH USE OF THE OVEN, ALWAYS CHECK THAT THE CONTROL KNOBS ARE TURNED TO 0 (OFF). 20 Presentation NEVER PLACE FLAMMABLE OBJECTS IN THE OVEN: IF IT SHOULD ACCIDENTALLY BE SWITCHED ON, THIS MIGHT CAUSE A FIRE. THE APPLIANCE BECOMES VERY HOT DURING USE. OVEN GLOVES SHOULD ALWAYS BE WORN. THE NAMEPLATE WITH THE TECHNICAL DATA, SERIAL NUMBER AND MARK IS IN A VISIBLE POSITION ON THE BACK OF THE OVEN. [. . . ] The flashing symbol will appear on the display. To set the current time, hold down START + STOP together until the display stops flashing. Now press START to increment the hour display. Once the current hour has been set, press STOP to set the minutes and increment them as before by pressing the START button. When the correct time is set, press the STOP button and the display will stop flashing. 25 Instructions for the User 4. 3 Program selection This oven has 10 different cooking programs, including: 5 preset programs (P1 to P5); 3 user-editable programs for fan-mode cooking (P6 to P8), 1 preheating program with user-editable temperature and start and end time (P9), 1 "easy" user-editable program for fan-mode cooking. The following table shows the parameters for each program. Uprh preheating temperature 170 °C 175 °C 180 °C 190 °C 200 °C Editable Editable Editable Editable Same as edited Ut°C Ut °C cooking temperature 170 °C 175 °C 180 °C 190 °C 200 °C Editable Editable Editable N/A Editable U Ct cooking time 20 minutes 20 minutes 20 minutes 20 minutes 20 minutes Editable Editable Editable N/A Editable Program Start/end Time N/A N/A N/A N/A N/A N/A N/A N/A Editable N/A P1 P2 P3 P4 P5 P6 P7 P8 P9 26 Instructions for the User 4. 4 Fan mode cooking Use the knob to select one of the preset programs (P1 - P5). The display shows the parameters of the selected program (tc = cooking time; temperature in degrees Centigrade and program number, e. g. Press START to confirm the start of the program. The program starts, performing the preheating stage; the display shows "PrEh". When the preheating is complete, a "BEEP" sounds to indicate that cooking can start. Press START or keep it pressed to increase the cooking temperature; each time START is pressed the temperature increments by 1°C (from 50° to 300°), or hold START down for increments of 5°C. Press STOP to move on to displaying the next parameter. Press START to display the cooking time. Press START or keep it pressed to increase the cooking time (from 1 min. Press STOP to complete the program editing procedure. The parameters set are now saved in the chosen program. Press START to display the parameters just set. Press START again to run the program just edited. 4. 7 Modifying a previously edited program To modify one of the programs, turn the knob to one of the programs from P1 to P9 edited previously. The parameters saved earlier will appear on the display. 28 Instructions for the User The display shows U t°C. [. . . ] Press STOP to complete the program editing procedure. Use absorbent kitchen roll; remove stubborn dirt with a damp sponge and ordinary detergent. 32 Instructions for the User 6. EXTRAORDINARY MAINTENANCE Occasionally, the oven will require minor servicing procedures or the replacement of parts subject to wear and tear, such as gaskets, light bulbs, etc. The specific operations for each procedure of this kind are provided below. Before carrying out any operation, disconnect the oven from the electricity supply. 6. 1 Changing the light bulb Remove the protective cover A. [. . . ]