User manual SMEG S809AE

[. . . ] THE MANUFACTURER DECLINES ALL RESPONSIBILITY FOR IMPROPER USE. DO NOT DISCARD PACKING IN THE HOME ENVIRONMENT. SEPARATE THE VARIOUS WASTE MATERIALS AND TAKE THEM TO THE NEAREST SPECIAL GARBAGE COLLECTION CENTRE. THE APPLIANCE MUST BE CONNECTED TO EARTH IN COMPLIANCE WITH ELECTRICAL SYSTEM SAFETY REGULATIONS. WHEN LINKING UP TO MAINS BY PLUG AND SOCKET, MAKE SURE THAT BOTH ARE COMPATIBLE AND CONNECT BY MEANS OF A POWER CABLE COMPLYING WITH APPLICABLE REGULATIONS. [. . . ] OVEN INSTALLATION The oven must be installed on a free-standing horizontal work top. The distance from the rear wall must allow easy access to the terminal board for connection of the power supply cable. Installation must be carried out by a qualified technician and in compliance with EEC DIRECTIVES currently in force. 2. 1 Electrical connection Make sure the voltage and the cross-section of the power cord match the specifications indicated on the identification plate positioned on the side of the oven. Do not remove this plate for any reason. ALFA241 For operation on 380-415V 3N~: use an H07RN-F type five-core cable (5 x 1. 5 mm2). ALFA341 For operation on 380-415V 3N~: use an H07RN-F type five-core cable (5 x 4 mm2). When linking up to mains by plug and socket, the connection must be completed with a plug of adequate capacity. The plug and wall-mounted socket must be of the same type (in accordance with CEI regulations). Make sure that the supply line is suitably earthed. If the appliance is connected to the electrical mains supply in a permanent manner, install a multipolar cut-out device on the line, with contact opening distance equal to or greater than 3 mm located near the appliance and in an easily reachable position. 25 Instructions for the installer WARNING: if the phase voltage drops below 190 VAC, the performance of the oven may suffer, not due to the product itself. The power socket located in the rear part of the oven must be used only to supply the extraction hood. The hood is provided as an optional accessory and has a maximum absorbed power of 300W. The terminal marked with this symbol connects parts together that are normally at zero potential. Connect the appliances appropriately using this terminal in order to make sure that they are equipotential. 2. 1. 1 How to reach the terminal board 1 2 Unscrew the fixing screws at the back of the side casing. Upon completion of the cooking cycle, the knob automatically returns to 0, the oven turns off and a buzzer signal is set off. The buzzer will switch automatically off after 20 seconds. STEAM SUPPLY KNOB This knob allows to select the most suitable amount of steam for the food to be cooked. Turning the knob clockwise, the selection options range from the 0 setting (no steam is supplied), to the 1 setting (maximum steam supply). Steam continues to be supplied until the knob is released; once released the knob automatically returns to the 0 setting. Note: The oven thermostat knob must be set between 150° and 250°C for steaming. 30 Instructions for the User 4. USING THE OVEN 4. 1 Warnings and general advice THE ALFA341 OVEN IS DESIGNED FOR A MAXIMUM LOAD OF 25 KG. THE ALFA241 OVEN IS DESIGNED FOR A MAXIMUM LOAD OF 12 KG. When using the oven for the first time, heat it up to a temperature of 200°C for a duration long enough to burn off any oily residues from the manufacturing process. As the oven door is opened, the heating elements and the fan are deactivated. To access food, always leave the door open as short a time as possible to prevent the temperature in the oven from falling and ruining the food. To prevent any steam in the oven from creating problems, the oven door has been equipped with a two-stage opening device: 1 turn the knob completely to the left and pull; 2 then turn it to the right to fully open the door. 1) 2) 31 Instructions for the User 4. 2 Oven inside lights The lights inside the oven come on automatically upon turning the thermostat knob. 4. 3 COOKING HINTS The lights inside the oven come on automatically upon turning the thermostat knob. [. . . ] CLEANING AND MAINTENANCE Important: Do not use a water jet for cleaning the inside of the oven. Before any intervention, disconnect the power supply of the oven. 5. 1 Cleaning stainless steel To keep stainless steel in good condition it should be cleaned regularly at the end of the day. To clean and preserve the stainless steel surfaces, always use only specific products that do not contain abrasives or chlorine-based acids. How to use: pour the product on a damp cloth and wipe the surface, rinse thoroughly and dry with a soft cloth or deerskin. Do not use metallic sponges or sharp scrapers: they will damage the surface. [. . . ]