User manual SMEG S852XV/A

[. . . ] Deep fat fryers must be continuously monitored during use: overheated oil can burst into flames. Do not flamb under the range hood; risk of fire This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance. 650 mm min. MAINTENANCE Switch off or unplug the appliance from the mains supply before carrying out any maintenance work. Clean and/or replace the Filters after the specified time period (Fire hazard). [. . . ] Clean the hood using a damp cloth and a neutral liquid detergent. The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product. EN 2 20 0 CHARACTERISTICS Dimensions max. 740 740 60 259 300 150 Min. 500mm 650mm 490 108 Components Ref. 1 2 2. 1 2. 2 9 10 14. 1 15 Q. ty Product Components 1 Hood Body, complete with: Controls, Light, Blower, Filters 1 Telescopic Chimney comprising: 1 Upper Section 1 Lower Section 1 Reducer Flange 150-120 mm 1 Damper 2 Air Outlet Connection Extension 1 Air Outlet Connection 260 433 90 15 14. 1 12a 7. 2. 1 9 10 11 2. 1 2 2. 2 12c Ref. Q. ty Installation Components 7. 2. 1 2 Upper Chimney Section Fixing Brackets 11 6 Wall Plugs 12a 6 Screws 4, 2 x 44, 4 12c 6 Screws 2, 9 x 9, 5 Q. ty Documentation 1 Instruction Manual 1 11 12a EN 2 21 1 INSTALLATION Wall drilling and bracket fixing 12 11 12a 650 min. 116 116 320 Wall marking: Draw a vertical line on the supporting wall up to the ceiling, or as high as practical, at the centre of the area in which the hood will be installed. Draw a horizontal line at 650 mm above the hob. Place bracket 7. 2. 1 on the wall as shown about 1-2 mm from the ceiling or upper limit aligning the centre (notch) with the vertical reference line. Mark the wall at the centres of the holes in the bracket. The suction speed and the remaining time before the hood shut down appear alternately The spot down at the right side flashes. By pressing the key the function is stopped After 100 working hours a FF appears. Charcoal filters have to replaced. F G H I L Keyboard lock: it is possible to jam the keyboard when, for example, cleaning the glass. By pressing the D-key (Intensive function) the keyboard block can be activated or deactivated. This function is confirmed by a Beep and by moving motor LEDS on display. EN 2 25 5 MAINTENANCE Metal grease filters Filters can be washed in the dish machine. They need to be washed when FF-sign appears on the display or in any case every 2 months, or even more frequently in case of particularly intensive use of the hood. Alarm reset Press the G-key for at least 2 seconds. Cleaning Remove the filters one at a time holding them up with one hand and pulling the handle downwards with the other hand at the same time. Make sure that filters are completely dry before putting them into their seat. (a possible modification of the filter surface doesn't influence its efficiency). Place the filters again into their seats and make sure that the handle of the filter remains outside. EN 2 26 6 Charcoal filter (recycling version) This filter cannot be washed or regenerated. [. . . ] Place the filters again into their seats and make sure that the handle of the filter remains outside. EN 2 26 6 Charcoal filter (recycling version) This filter cannot be washed or regenerated. It has to be replaced when the EF appears on the display or at least once every 4 months. Activation of the alarm signal In the recycling version hoods the filter saturation alarm has to be activated during the installation or later. Press the E-key for about 5 seconds until the LED on the display start to move. [. . . ]