User manual SMEG SC106

[. . . ] PRECAUTIONS FOR USE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 DISPOSAL INSTRUCTIONS - OUR ENVIRONMENT POLICY . . . . . . . . . . . 34 SAFETY PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 GET TO KNOW YOUR OVEN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] After setting the duration, press PT1 once. The symbol and the current time will appear on the display. Turning PT1 to the right increases the time, allowing the cooking start time required to be set. A few seconds after the required duration is set, the and symbols will stop flashing, and the oven will start to wait for the starting time set. At the end, the word STOP will appear on DSP1, cooking will stop and a buzzer will sound; press PT1 once to deactivate it. If you wish to continue cooking beyond the set time, press PT1 again. The oven will restart normal operation with the cooking settings selected previously. Turn PT2 to the 0 to switch the oven off completely. Modifying the data set Once automatic cooking has started, its duration can be changed. When the and symbols are steady and cooking is in progress, or the oven is in standby status waiting for cooking to start, press PT1 once. The symbol starts flashing and PT1 can be turned to change the set duration. Press PT1 again; the symbol goes out, the symbol will start to flash, and the cooking start time will be displayed on DSP1. The cooking start time can be increased or decreased by turning PT1. A few seconds after the last change, the e symbols will appear (in steady mode) on DSP1 and automatic cooking will restart with the new settings. 42 Instructions for the user 7. 6 Secondary menu This appliance also has a "secondary menu" allowing the user to: 1 2 Set the time shown on the display (DSP1). (P1: OF / ON) Activate or deactivate the child safety lock ( ; this function locks out all the functions and knobs after 2 minutes of operation without any command from the user (when this system is active, the symbol appears on DPS1). To exit the lockout status temporarily to modify a cooking program or select a different function, keep PT1 pressed until the symbol disappears from DSP1. The required changes can now be made, and 2 minutes after the last setting is made the lockout will come into operation again. To deactivate the lockout permanently, access the secondary menu and switch the function off as described in this section. (P2: OF / ON) Activate or deactivate the Show Room function, which disables all the heating elements so that only the control panel works. To allow the oven to be used normally, P2:OFF must be set. 3 (P3: OF / ON) Activate or deactivate the function which limits the maximum power absorption to 2300 W. When the child safety lock is activated (P1:ON), if a knob is turned "bLOC" appears on DSP1 for 2 seconds. Operating PT2 also triggers the "BLOC" alarm until the function originally selected is restored. 4 43 Instructions for the user 7. 6. 1 Modifying the secondary menu settings The secondary menu appears the first time the appliance is used or after a power blackout, or can be accessed by keeping PT1 depressed for 3 seconds with the oven in OFF status (see point "7. 2 Operating modes"). [. . . ] If the door should close during these operations, simply relock one of the hinges as described in point "12. 2 Removing the door". The panes of glass can now be washed separately. Use absorbent kitchen roll; remove stubborn dirt with a damp sponge and ordinary detergent. Warning: before removing the panes of glass, make sure that at least one of the door's hinges has been locked in open position as described in points "12. 2 Removing the door". This operation might have to be repeated during the glass removal process if the door is accidentally freed. [. . . ]