User manual SMEG SE2541

[. . . ] 42 Safety cut-out device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Residual heat indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Practical hints for use of the cooking zones . . . . . . . . . . . . . 43 General advice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Always disconnect the appliance from the electricity supply before any adjustments, maintenance, etc. 36 Electrical connection Make sure that the mains electricity supply in the home is of the voltage and power indicated on the date plate underneath the hob. Use a cable of type H05RRF or H05RNF, bearing in mind that the earth wire (yellow-green) must be about 20 mm. Longer at the end for connection to the appliance. Make sure that the lead is not in contact with heated zones. On installation, provide an omnipolar circuit breaker with minimum distance between contacts at least 3 mm on the appliance power supply line, at a point easily reached from the appliance. The options for connection to the electrical mains are indicated in the tables below or on the data plate underneath the hob. Cables H 05 RRF - H 05 RNF Minimum gauge in mm 2 230V~ 2, 5 400V 3N~ 1, 5 400V 2N~ 2, 5 To access the terminal board press the two side tabs as indicated on the terminal board cover. Modify the arrangement of the jumpers on the terminal board if necessary, then fix the wires, making sure that the earth wire is about 20 mm longer. Fix the power supply lead to the terminal and pass it through the hole in the lid. 37 Before making the connection to the electrical mains and using the ceramic hob, check that the protective lid has been fixed back in place, and ensure that the earth connection is in good working order. NEVER TOUCH THE ELECTRONIC CIRCUIT BOARD IN ANY CIRCUMSTANCES. Our company declines any responsibility for injury or damage deriving from failure to make the earth connection or inadequate connection to earth. 38 Using the hob The appliance has 4 cooking zones of different diameter and power. Their positions are clearly indicated by rings and the heat is only released inside the diameters marked on the hob. Radiant high-light zones switch on after a few seconds and have 9 heat settings (minimum 1, maximum 9). This device is equipped with capacitive recognition keys. Touching any of the keys with a fingertip will activate the corresponding command. The appliance will recognize your request and give a short beep. Touch-control keys (see page 40) Mod. SE 2741 1 2 3 4 5 6 7 8 9 Front left-hand cooking zone Back left-hand cooking zone Back right-hand cooking zone Front right-hand cooking zone Dual circuit light switch-on Residual heat indicators by zone (+60°C) ("H"blinking) Master on/off key Control disabling key Cooking zone controls 210 (120) 1400+700 W 145 180 145 1200 W 1800 W 1200 W Mod. SE 2752 210 (120) 145 170 x 265 180 1400+800 W 1200 W 1400+800 W 1800 W 10 Heat power regulator switch (9 positions - from 1 to 9) 39 40 Switching on the cooking zones A) Simply touch the key two times consecutively within 2 seconds to switch on the appliance. Wait for a first beep and then touch the key again until the pilot light on the left of the key illuminates. B) Select the cooking zone required, such as number 0 appears). (the C) Press the or key to select the power required from 1 to 9, this can also be modified during key to start from power cooking (press the setting 9). D) By using the key signal 9 flashes and the cooking area is activated at maximum power. Within 15 seconds (during which time the 9 continues to flash) it is possible to take advantage of the automatic heating function. [. . . ] The hob glass is very tough but not shatterproof: it may be damaged by violent knocks with hard or sharp objects. In case of breakage, cracking or crazing, the glass must not be used again and the appliance must be disconnected from the electrical mains immediately. You are advised to contact the after­sales service. During testing, the hob may give off an acrid smell or a smell of burning which will disappear completely in a few minutes. [. . . ]