User manual SMEG SE435XT

[. . . ] A diagram is screen-printed on the front panel. This diagram indicates to which electric plate the knob in question corresponds (see fig. A red warning light will come on to indicate that the plate has been ignited. 2) HOW TO USE THE ELECTRIC PLATES A purely indicative plate regulation chart is given below. TABLE NORMAL AND RAPID PLATE 0 1 2 3 4 5 6 1 1-4 4-8 8 - 10 10 - 12 12 THERMOSTAT PLATE HEAT INTENSITY Off Weak Low Slow Medium Strong High To dissolve butter, chocolate, etc. . To prepare cremes and suces requiring long slow cooking times. [. . . ] Incorrect installation could cause damage to persons, animals and property for which the manufacturer cannot be held responsible. - Overturn the hob and correctly position seal "E" (fig. 6) under the edge of the hob itself, so that the outer part of the seal itself perfectly matches the outer perimetral edge of the hob. The ends of the strips must fit together without overlapping. - Evenly and securely fix the seal to the hob, pressing it in place with the fingers. - Remove the strip of protective paper from the seal "F" it the hooks into their relative housings "K" in the unit and set the hob into the hole in the cabinet. Lock it in place with the relative fixing screws "F" (see fig. WARNINGS: Be aware that the glue that join the laminated plastic to the furniture, has to resist to temperature not below 150° C, to avoid the unstuck of the panelling. The installer should bear in mind that the mixed appliance is the Y type. The rear wall, adjacent and surrounding surfaces must therefore be able to withstand an overtemperature of 65K. 4) INSTALLING THE HOT PLATE Check that the appliance is in a good condition after having removed the outer packaging and internal wrappings from around the various loose parts. In case of doubt, do not use the appliance and contact qualified personnel. Never leave the packaging materials (cardboard, bags, polystyrene foam, nails, etc. ) within children's reach since they could become potential sources of danger. The measurements of the opening made in the top of the modular cabinet and into which the hot plate will be installed are indicated in either fig. 4, comply with the measurements given for the hole into which the appliance will be recessed (see fig. If a wood is installed above the hob, please look at the hood manufacturer instructions regarding the minimum distance between hood and hob (fig. 5). 5) FIXING THE HOT PLATE The hob has a special seal which prevents liquids from infiltrating into the cabinet. Strictly comply with the following instructions in order to correctly apply this seal: - Detach the seals from their backing, checking that the transparent protection still adheres to the seal itself. FIG. 7 6 INSTALLATION 6) ELECTRICAL CONNECTIONS Electrical connection must be carried out in compliance with the specifications and provisions in force. Before proceeding with the connections, check that: - The voltage rating of the appliance and the current sockets suits the maximum power draw of the appliance (see data label affixed to the lower part of the appliance itself). - The system is equipped with an efficient earth connection in compliance with the pertinent provisions in force. The manufacturer declines all responsibility for failure to comply with these provisions. - If the appliance has no power cable, connect a cable of adeguate section to the terminal strip (consult the table on next page) complying with the wiring diagram of fig. [. . . ] In case of substitution of the input cable, the installer must keep the "earth" conductor longer than "live" ones, and must respect the cautions in paragraph "Electrical connection". To reassemble the appliance repeat the inverse process. 8) REPLACING THE ELECTRICAL COMPONENTS For access to the various parts, remove the hotplate from the top of the cabinet. Then overturn it, unscrew screw "Z" and remove under part. After these actions is possible to work on the plates, commutators, clamps and input cable. 9) TECHNICAL CHARACTERISTICS OF THE ELECTRICAL COMPONENTS To facilitate the job of the installer we present a scheme with the characteristics of the components. POWER OF ELECTRICAL COMPONENTS DENOMINATIONS W Denominations Normal plate Ø 145 mm Normal plate Ø 180 mm W 1000 1500 TYPE AND SECTION OF THE POWER CABLES Cable type Single phase power 110 V~ 3 X 4. 5 mm2 (*) 5 X 2. 5 mm2 (*) 3 X 4. 5 mm2 (*) 4 X 2. 5 mm2 (*) Three phase power 220 V 3N ~ Three phase power 220 V 2N~ Rubber H05 RR-F Polycroropene H05 RN-F (*) keeping in mind the contemporaneousness factor 9 TECHNICAL DATA MODEL WITH 4 NORMAL PLATES VOLTAGE FREQUENCY TOT. [. . . ]