User manual SMEG SF390X

[. . . ] 9 CLEANING AND MAINTENANCE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 POSITIONING IN THE COUNTER TOP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 ADAPTATION TO DIFFERENT TYPES OF GAS . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 FINAL OPERATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Correct disposal enables intelligent recovery of valuable materials. Before disposing of your appliance it is important to remove doors and leave shelves in the same position as for use, to ensure that children cannot accidentally become trapped inside during play. It is also necessary to cut the connecting cable to the power grid, removing it along with the plug. 8 Instructions for the user 4. USING THE HOB 4. 1 Lighting the hob burners Before lighting the hob burners, check that the flame-spreader crowns are correctly in place with their respective burner caps, making sure that the holes 1 in the flame-spreaders are aligned with the plugs 3 and thermocouples 2. To prevent damage to the work top, the hob comes complete with a raised pan stand 4: This must be placed under pans with a diameter greater than those indicated in the table in point "4. 3 Cookware diameters". In any case, pans with a diameter greater than 28 cm must be used solely on the central burner. The pan stand 4 can also be used with woks. 4 1 2 3 1 2 3 The burner controlled by each knob is shown next to the knob. The appliance is equipped with an electrical ignition device. Simply press the knob and turn it anti-clockwise to the maximum flame symbol , until the burner lights. On valved models, once the burner is lit, keep the knob pressed for a few seconds to give the thermocouple time to heat up. The burner may go out when the knob is released: in this case, the thermocouple has not heated up sufficiently. This appliance can be mounted against walls higher than the worktop on condition that a distance of "1" be kept between the appliance and the wall as shown in the figure so as to avoid damage from overheating. Make sure that there is a minimum distance of 750 mm between the stoves and any shelf that may be installed directly above it. Carefully position the supplied insulating seal “2” on the outer perimeter of the hole made in the counter top as shown in the figure below, trying to make it stick on the entire surface by applying light pressure on it with your hands. The front and rear sides of the seal must brush against the hole. Once these operations have been carried out, place the hob on the insulating seal and fix it to the supporting structure using screws and fastening brackets so that the hob is perfectly flat. The brackets shown in the figure should be placed only after the hob has been built in. 6 73 750 1 ÷ 20 50 15 0 2 50 84 7 48 2 1 2 3 4 12 Instructions for the installer Carefully trim the surplus away from edge beyond the seal. The dimensions given in figure 2 refer from the hole to the inside of the seal. Dimensions: Gas and electrical connection location (measurements in mm). 866 267 76 73 34 38 474 511 70 3, 3 833 13 Instructions for the installer Max 150 mm Min. 20 mm Max 100 mm IMPORTANT: if the appliance is mounted on a unit, make sure that a separating shelf is installed, as shown in the figure. If the appliance is instead on an oven installed under the hob, there is no need to install a separating shelf. If installed on top of an oven, the latter must be equipped with a cooling fan. 14 Instructions for the installer 6. 2 Clearances above and around domestic appliances Extract from AS5601 REQUIREMENTS 1 Overhead clearances – (Measurement A) Range hoods and exhaust fans shall be installed in accordance with the manufacturer’s instructions. However, in no case shall the clearance between the highest part of the hob of the cooking appliance and a range hood be less than 600 mm or, for an overhead exhaust fan, 750 mm. [. . . ] On completion of the installation, the installer MUST check for gas leaks and test each burner individually for the correct flame. Once all burners have been tested individually, turn all burners on together. Warranty service calls do not cover these adjustments!To check the operating pressure of the appliance it is recommended at least 2 large size burners are used. [. . . ]