User manual SMEG SF521N

[. . . ] 9 USING THE HOB. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 CLEANING AND MAINTENANCE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 POSITION NEAR THE COUNTER TOP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 ADAPTATION TO DIFFERENT TYPES OF GAS . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] It can constitute a suffocation hazard for children, especially the plastic bags. Your old appliance also needs to be disposed of correctly. Important: hand over your appliance to the local agency authorised for the collection of electrical appliances no longer in use. Correct disposal enables intelligent recovery of valuable materials. Before disposing of your appliance it is important to remove doors and leave shelves in the same position as for use, to ensure that children cannot accidentally become trapped inside during play. It is also necessary to cut the connecting cable to the power grid, removing it along with the plug. 8 Instructions for the user 4. DESCRIPTION OF THE CONTROLS 1 2 3 Auxiliary Burner (AUX) Rapid Burner (R) Double crown Burner (UR2) KNOB DESCRIPTION To light the flame, press the knob and, at the same time, turn it anticlockwise to the maximum flame symbol . To adjust the flame, turn the knob to the zone between the maximum ( ) and minimum ( ) settings. position. To turn off the burner, turn the knob to the ARRANGEMENT OF BURNERS AND DESCRIPTION OF SYMBOLS Front Auxiliary burner UR2 External crown Back Rapid burner UR2 Internal crown 9 Instructions for the user 5. USING THE HOB Before lighting the hob burners, check that the flame-spreader crowns are correctly in place with their respective burner caps, making sure that the holes A in the flame-spreaders are aligned with the igniters and thermocouples. For the UR2 double burner, place and fit perfectly the burner caps G and E on the flame-spreader crowns F and D. The latter have to be placed on support C and then fitted in the base B. 6. 2. 2 Pan stands Remove the pan stands and clean them with lukewarm water and non-abrasive detergent, making sure to remove any encrustations. These components must not be washed in the dishwasher. 6. 2. 3 Burner caps and flame-spreader crowns The burner caps and flame-spreader crowns can be removed for easier cleaning. Wash them in warm water and non-abrasive detergent making sure to remove any encrustation, then wait until they are perfectly dry. Refit the burner caps on the appropriate crowns and make sure that the flame-spreader crowns are correctly positioned in their housings with their respective burner caps. 6. 2. 4 Igniters and thermocouples For correct operation the igniters and thermocouples must always be perfectly clean. Check them frequently and clean them with a damp cloth if necessary. Remove any dry residues with a wooden toothpick or a needle. 13 Instructions for the installer 7. POSITION NEAR THE COUNTER TOP The following operation requires building and/or carpentry work so must be carried out by a competent tradesman. Installation can be carried out on various materials such as masonry, metal, solid wood or plastic laminated wood as long as they are heat resistant (T 90°C). 7. 1 Fixing to a support structure model with traditional casing (fig. 1) Create an opening with the dimensions shown in the figure in the top surface of the counter, keeping a minimum distance of 50 mm from the rear edge. This appliance can be mounted against walls higher than the work surface on condition that a distance of "X" be kept between the appliance and the wall as shown in the figure so as to avoid damage from overheating. [. . . ] Ensure appliance is secured to wall when installation is completed. The regulator supplied must be fitted to the ½ BSP thread at the rear of the appliance. An approved manual shut-off valve must be installed. regulator must be checked and adjusted to 1. 0kPa after installation. [. . . ]