User manual SMEG SPR876AVOGH

[. . . ] A different temperature can be set using the “Temp. ” button The following adjustments are possible: Leds lit High (less cold) Medium-high Intermediate Medium-low Low (colder) Set temperature DE GB FR NL ES PT IT GR SE NO DK FI What to do if. . . Possible causes: The control panel is There may be an appliance switched off, the appliance power supply problem. does not work. Cures: Make sure: - there is not a power outage - the plug is properly inserted in the power socket and the mains double-pole switch (if present) is in the correct position (i. e. allows the appliance to be powered) - the household electrical system protection devices are efficient - the power cable is not broken. [. . . ] To reinstate the Meat & Fish compartment, make sure to refit the drawer cover before inserting the drawer and reactivating operation. Press the “Meat & Fish compartment function” button on the control panel for 3 seconds, until the yellow indicator goes off. To optimise energy consumption, it is advisable to deactivate the Meat & Fish compartment and remove its components (except the shelf above the crisper drawers). Removing the Meat & Fish compartment: Fig. 2 13 “ZERO DEGREES” BOX (depending on the model) The “Zero Degrees” box is specifically designed to maintain a low temperature and a suitable humidity level, in order to keep foods fresher for longer (e. g. meat, fish, fruit and winter vegetables). Activating and deactivating the box To activate the compartment, press the button shown in the figure for more than 1 second, until the symbol lights up The temperature inside the box, when active, is approximately 0°. The symbol lit indicates that the compartment is functioning. Press the button again for more than 1 second to deactivate the compartment The following factors are vital for the “Zero Degrees” box to work properly: - the refrigerator compartment must be switched on - the temperature of the refrigerator compartment must be between +2°C and +6°C - the box must be inserted to enable activation - no special functions must have been selected (Standby, Cooling-Off, Vacation – where applicable). If one of these special functions has been selected, the “Zero Degrees” box must be deactivated manually, and any fresh food inside it removed. If manual deactivation does not take place, the box will be deactivated automatically after 8 hours. Note: - if the symbol does not light up when the box is activated, check that the box is properly inserted; if the problem persists, contact your nearest authorized After-sales Service - if the box is active and the drawer open, the symbol on the control panel may be deactivated automatically. If the drawer is inserted, the symbol will become active again - irrespective of the state of the box, a slight noise may be heard: this is normal and is not a cause for concern. - when the box is not active, the temperature inside it depends on the general temperature inside the refrigerator compartment. • Avoid, or reduce temperature variations to the minimum. Respect the best-before date on the package. • Always follow the storage instructions on the frozen food packages. Making ice cubes • Fill the ice cube tray 2/3 full and place it in . the compartment • Do not use sharp or pointed instruments to detach the tray if it is stuck to the bottom of compartment. the • Bend the ice tray slightly to remove the cubes. Fig. 2 16 How to defrost the appliance Before defrosting the appliance, unplug it or switch off the power at the mains. Defrosting of the refrigerator compartment is completely automatic. Droplets of water on the rear wall of the refrigerator compartment indicate that the periodic automatic defrost cycle is in progress. The defrost water is automatically routed to a drain outlet and into a container from which it evaporates. Clean the defrost water drain outlet regularly using the tool supplied with the appliance in order to ensure defrost water is removed correctly. [. . . ] Disconnecting the appliance It must be possible to disconnect the appliance by unplugging it or by means of a two-pole switch fitted upline of the socket. 19 ELECTRICAL CONNECTION FOR GREAT BRITAIN AND IRELAND ONLY Warning - this appliance must be earthed Fuse replacement If the mains lead of this appliance is fitted with a BS 1363A 13amp fused plug, to change a fuse in this type of plug use an A. S. T. A. approved fuse to BS 1362 type and proceed as follows: 1. Remove the fuse cover (A) and fuse (B). 2. Fit replacement 13A fuse into fuse cover. Important: The fuse cover must be refitted when changing a fuse and if the fuse cover is lost the plug must not be used until a correct replacement is fitted. [. . . ]