User manual SMEG ST8649U MANUALE D'INSTALLAZIONE

[. . . ] DISHWASHER INSTALLATION INSTRUCTIONS CONTENTS Contents 1 2 3 3. 1 4 5 5. 1 5. 2 5. 2. 1 5. 2. 1. 1 5. 2. 1. 2 5. 2. 2 5. 3 5. 3. 1 5. 3. 2 5. 3. 3 5. 4 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 INSTALLATION MATERIAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Kit supplied with dishwasher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Use a spirit level to check the appliance is perfectly level (ref. Leveling is vital for assuring correct dishwasher operation. Make sure to leave a gap of at least 3 mm (7/64”) between the top of the dishwasher and the worktop (ref. 5-01 12 INSTALLATION INSTRUCTION EN Fig. 5-02 5. 2 Connections Install the dishwasher so as to allow ease of access to the electrical and hydraulic connections through the adjacent unit. These connections must never be behind the dishwasher. The inlet and drain hoses can be pointed in all directions. make sure that they are not bent, crushed or too tight. Tighten the ring nut after pointing the hoses in the required direction. Figure 5-03 indicates the distances to maintain between the dishwasher and the various connections. • Recommended temperature: 49°C (120°F), max. • Recommended water pressure: 0. 5 - 9 bar (7 -130 PSI). If the pressure is too high, fit a pressure reducer. A rubber hose connected to a sink spray may burst if installed on the same pipes feeding the dishwasher. If your sink is fitted with this accessory, remove the hose and plug the hole. EN Fig. 5-05 15 EN INSTALLATION INSTRUCTION Do not cut the inlet hose (see fig. If the hose is cut, the dishwasher will not work, water will leak and you may be injured. If the hose is too long, wind it up tidily and place it behind the appliance. The cable harness and electrical components must not come into contact with the hydraulic system and the water inlet and drain hoses. Fig. 5-06 When connecting the dishwasher drain hose to the sink make sure that the hose is not bent (ref. 5-07) in order to prevent cracks or breakages that could damage it. A Fig. 5-07 16 INSTALLATION INSTRUCTION 5. 2. 1. 2 Connecting the drain hose Connecting to a drain Insert the relative hose into a drain with a minimum diameter of 4 cm (1-37/64”) (ref. [. . . ] N. B. : the screws are not supplied. Fig. 5-20 Attach the door panel: fit the hooks into their slots on the dishwasher and allow the panel to slide downwards and slip in to place (see fig. 5-21 26 INSTALLATION INSTRUCTION Secure the door to the panel with the supplied screws. The panel must have a minimum thickness of 20 mm (25/32”) (see fig. [. . . ]