User manual SMEG STX645

[. . . ] 9 Switching off. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 ENERGY SAVING AND ENVIRONMENTAL RESPECT. Reducing the consumption of detergent and respecting the environment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] 2-02) which is used to program the appliance and switch it on and off. 2 end 3 4 1 Fig. 2-02 To select the most suitable program for the dishes to wash, consult the following table which specifies the most appropriate type of washing sequence depending on the kind of dishes and how dirty they are (see tab. 2-02). 6 Rev 0. 0 USER INSTRUCTIONS PROGRAM NUMBER AND SYMBOL DISHES AND CUTLERY PROGRAM SEQUENCE TIME MINUTES (1) 16’ CONSUMPTION ENERGY WATER KWh (1) 4. 1 l 1. 08 gal. 0. 02 EN 1 RINSE Pans and dishes waiting Cold pre-wash for further washing Immediate washing after use for moderately dirty dishes Wash at 45°C (113°F). Dry. 2 LIGHT 58’ 11. 5 l 3. 04 gal. 0. 53 3 ECO Normally dirty dishes 120’ 16 l 4. 23 gal. 1 4 NORMAL Immediate washing after use for normally dirty dishes 111’ 16. 3 l 4. 31 gal. 0. 68 5 SUPER Very dirty pans and dishes (except delicate items) 117’ 20 l 5. 28 gal. 1. 25 Tab. 2-02 (1) The cycle times listed in the use and care manual are based on normal soil loads and 49°C (120°F) incoming water and will vary based on your actual conditions. Rev 0. 0 7 EN USER INSTRUCTIONS Only run the soak program with half loads. After using the above table to choose the most suitable washing cycle, program the appliance. Before starting a washing program, make sure that: • The water supply tap is open. • There is regenerating salt in the water softener tank (to add salt, see the instructions in the general manual). • The correct amount of detergent has been added to the dispenser (to add detergent, see the instructions in the general manual). • The spray arms are able to rotate freely and without obstruction. • The racks have been correctly loaded (see the instructions in the general manual). • The dishwasher door is securely closed. 2. 2. 1 Switching on Press the on/off button (ref. Then wait for one of the program indicator lights to turn on (ref. 2-02). 2. 2. 2 Selecting and starting the program • Press the program selection button (ref. 2-02) several times until the indicator light corresponding to the required program turns on (ref. 2-02); • if necessary, select, using the relative buttons, the complementary functions you are interest in (e. g. “Programming delay”); • close the door; the program will start after about 2 seconds and the relative indicator light will flash throughout the cycle (program running signal). If the door of the dishwasher has not been closed or has been incorrectly closed, the washing cycle will not begin. 2. 2. 3 End of program The end of the program is indicated by a brief acoustic signal and the (marked by “end”) “normal” and “super” program indicator lamps flash. 8 Rev 0. 0 USER INSTRUCTIONS 2. 2. 4 Interrupting a program To interrupt the current program simply open the door of the dishwasher; to restart the program, simply close the door again. The program restarts from where it was interrupted. [. . . ] Water pump-out malfunction The appliance does not pump out the water or does so incorrectly. Make sure the drain hose is not kinked or crushed and that the siphon and filters are not clogged. If the problem persists, contact the technical assistance service. end E5 end E6 Tab. 4-01 Light off Light on Light flashing Rev 0. 0 13 EN USER INSTRUCTIONS If an alarm situation occurs, the dishwasher interrupts the current program and signals the fault. [. . . ]