User manual SMEG UK60MFX1

[. . . ] This appliance is intended for domestic uses and conforms to current regulations in force. Retain this information for future reference. The appliance has been built to carry out the following functions: cooking and heating-up of food. The manufacturer declines all responsibility for improper use. [. . . ] The food should be placed on the oven shelf which is positioned on one of the guides supplied with the different ovens, following the instructions below: Food Flat or thin meat Rolled roast joints Poultry Grille on the shelf 4 3-4 4 Storage compartment A storage compartment, accessible by pulling on the top edge of the door, is located beneath the ovens. Never store flammable materials such as rags, paper or the like. The compartment is intended only for holding the metal accessories of the range. 2 Use the or keys to select the symbol lenght of time required. The will appear on the display. 1 Minute-timer key 2 Cooking period key 3 End time key 4 Decrease time key 5 Increase time key After set-up, to see the remaining time, press the "minute timer" key. Use as a minute counter does not interrupt functioning of the oven at the end of the programmed time. To set the oven to switch off automatically after a set period: (only for main oven) Use this function if you have already started cooking and want the oven to switch-off at the end of cooking time. (for example after 45 minutes) 1 Press the "cooking period" key, the display lights up, showing 00:00. 2 Use the or keys to set the desired cooking time. The `A' simbol will appear on the display, and the current clock time will be shown. After set-up, to see the cooking time remaining, press the "cooking period" key; to see the end of cooking time press the key "end time key". Before setting the programmer for semi/automatic cooking, activate the desired function and temperature. Set the clock: When using the oven for the first time, or after a power failure, the display flashes regularly and indicates 00:00. Press the keys "cooking period" key and "end time key" at the same time the keys or : each single press changes the time by 1 minute either up or down. 14 To set the oven to switch off automatically at a set time: Use this function if you have already started cooking and want the oven to switch-off at a set time. Before lighting the hob burners check that the flame caps are in the correct position and that their burner caps are in place, making sure that the holes A in the flame caps correspond to the spark plugs and thermocouples. To prevent deterioration of the hob the appliance is equipped with a raised pan stand to be placed underneath pans more than 26 cm in diameter. The supplied reduction rest is used also for small pans. Lighting of the hob burners This optional grid is for use with "woks" (Chinese pans). The drawing next to each knob shows the corresponding burner. The appliance has an electronic lighting device. Simply press and turn the knob anticlockwise to the minimum flame symbol , until the flame is lit. Hold the knob down for a few seconds to allow the thermocouples to heat up. The burner may go out when the knob is released: this is because the thermocouple has not been sufficiently heated. Repeat the operation holding down the knob a little longer. This operation is not necessary for burners without thermocouples. (cm) 12 16 18 18 14 24 26 26 In the event of a power failure the burners can be lit with a match or gas lighter. The flame failure devices will continue to function normally. 1 Auxiliary 2 Semi rapid 3 Rapid 4 Triple crown Practical advice for using the hob burners For better use of the burners and lower gas consumption, use covered vessel that are proportional in size to the burner to prevent the flame from licking the sides. [. . . ] Screw the assembly to the moveable connector A of the appliance, placing the seal C between them. When making the connection, make sure that no stress of any kind is applied to the cooker and that the hose does not touch any sharp edges. If connecting to LPG the bayonet hose must have red bands on it. Replacement of nozzles on the hob To change the nozzles, proceed as described below: 1 Extract the grids and remove all the caps and flame-spreader crowns; 2 Unscrew the burner nozzles with a 7 mm socket wrench; 3 Replace the nozzles according to the type of gas to be used 4 Replace the burners in the correct position. Adaptation to different types of gas Warning!Before performing any cleaning or maintenance work, disconnect the appliance from the mains. [. . . ]